I am having trouble accessing my FujiFilm FinePix 3800 camera in Raw Hide (it worked perfectly in FC1 and earlier).

When I connect it and turn it on, logs get:

usb 1-1: new full speed USB device using address 8 SCSI subsystem initialized Initializing USB Mass Storage driver... scsi0 : SCSI emulation for USB Mass Storage devices USB Mass Storage device found at 8 drivers/usb/core/usb.c: registered new driver usb-storage USB Mass Storage support registered.

and the usb_storage and scsi_mod modules get loaded. However, the camera does not seem to get "attached" to any specific /dev/xyz (or /udev/xyz for that matter) - e.g. when I try to access /dev/sda, I get "No such device or address".

% cat /proc/scsi/scsi Attached devices:

% cat /proc/scsi/usb-storage/0 Host scsi0: usb-storage Vendor: Unknown Product: USB Mass Storage Serial Number: Y-406^^^^^030528XFPX0007040092 Protocol: 8070i Transport: Control/Bulk/Interrupt Quirks:

% cat /proc/bus/usb/devices

T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0000 ProdID=0000 Rev= 2.06 S: Manufacturer=Linux 2.6.5-1.319custom uhci_hcd S: Product=UHCI Host Controller S: SerialNumber=0000:00:1d.0 C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms

T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 8 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=04cb ProdID=011a Rev=10.00 S: Product=USB Mass Storage S: SerialNumber=Y-406^^^^^030528XFPX0007040092 C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA I: If#= 0 Alt= 0 #EPs= 3 Cls=08(stor.) Sub=05 Prot=00 Driver=usb-storage E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=83(I) Atr=03(Int.) MxPS= 8 Ivl=1ms

I tried both 2.6.5-1.322 and 2.6.5-1.319custom (kernel-source recompiled using stock config-i686 with 4G and 4G+4G disabled, APM disabled, SOFTWARE_SUSPEND enabled).

Am I doing something wrong? Or is this a bug (and should be reported)? Is there some way to make it work? Thanks a lot for any help.

P.S. Other USB devices (printer, mouse) work OK.