Same here, 2.6.27-0.287.rc4.git7.fc10.i686 does not boot but 2.6.27-0.244.rc4.git1.fc10.i686 is ok
Without rhgb but with quiet the messages are:
stabilized: stat /proc/bus/usb/devices: No such file or directory mount: error mounting /dev/root on /sysroot as ext3: No such file or directory setuproot: moving /dev failed: No such file or directory setuproot: error mounting /proc: No such file or directory setuproot: error mounting /sys: No such file or directory Mount failed for selinuxfs on /selinux: No such file or directory switchroot: mount failed: No such file or directory sd 0:0:0:0: [sda] Assuming drive cache: write through sd 0:0:0:0: [sda] Assuming drive cache: write through
I'll copy out the full messages from the kernel and post when I have them. This will take ages though.
Hardware is an Asus Eee PC 4G with rawhide installed on an 8GB SDHC card in the built-in reader. Fedora 9 kernels were ok as was 2.6.27-0.244.rc4.git1.fc10
2008/8/29 Andrew Gormanly a.gormanly@ucl.ac.uk
Same here, 2.6.27-0.287.rc4.git7.fc10.i686 does not boot but 2.6.27-0.244.rc4.git1.fc10.i686 is ok
Without rhgb but with quiet the messages are:
stabilized: stat /proc/bus/usb/devices: No such file or directory mount: error mounting /dev/root on /sysroot as ext3: No such file or directory setuproot: moving /dev failed: No such file or directory setuproot: error mounting /proc: No such file or directory setuproot: error mounting /sys: No such file or directory Mount failed for selinuxfs on /selinux: No such file or directory switchroot: mount failed: No such file or directory sd 0:0:0:0: [sda] Assuming drive cache: write through sd 0:0:0:0: [sda] Assuming drive cache: write through
I'll copy out the full messages from the kernel and post when I have them. This will take ages though.
Hardware is an Asus Eee PC 4G with rawhide installed on an 8GB SDHC card in the built-in reader. Fedora 9 kernels were ok as was 2.6.27-0.244.rc4.git1.fc10
-- Andrew Gormanly London Centre for Nanotechnology University College London Tel: 020 7679 3400 17-19 Gordon Street Fax: 020 7679 0595 London WC1H 0AJ a.gormanly AT ucl.ac.uk
-- fedora-test-list mailing list fedora-test-list@redhat.com To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-test-list
I am booting off an external USB hard drive and I am running on Intel motherboard, if this can help.
2008/8/29 Andrew Gormanly a.gormanly@ucl.ac.uk
Same here, 2.6.27-0.287.rc4.git7.fc10.i686 does not boot but 2.6.27-0.244.rc4.git1.fc10.i686 is ok
Without rhgb but with quiet the messages are:
stabilized: stat /proc/bus/usb/devices: No such file or directory mount: error mounting /dev/root on /sysroot as ext3: No such file or directory setuproot: moving /dev failed: No such file or directory setuproot: error mounting /proc: No such file or directory setuproot: error mounting /sys: No such file or directory Mount failed for selinuxfs on /selinux: No such file or directory switchroot: mount failed: No such file or directory sd 0:0:0:0: [sda] Assuming drive cache: write through sd 0:0:0:0: [sda] Assuming drive cache: write through
I'll copy out the full messages from the kernel and post when I have them. This will take ages though.
Hardware is an Asus Eee PC 4G with rawhide installed on an 8GB SDHC card in the built-in reader. Fedora 9 kernels were ok as was 2.6.27-0.244.rc4.git1.fc10
-- Andrew Gormanly London Centre for Nanotechnology University College London Tel: 020 7679 3400 17-19 Gordon Street Fax: 020 7679 0595 London WC1H 0AJ a.gormanly AT ucl.ac.uk
-- fedora-test-list mailing list fedora-test-list@redhat.com To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-test-list
I see similar message: but if usb devices are not started, where shall I see the log for the aborted boot????
stabilized: stat /proc/bus/usb/devices: No such file or directory Reading all physical volumes.This may take a while Volume group "VolGroup00" not found Unable to access resume device (dev/VolGroup00/LogVol01) mount: error mounting /dev/root on /sysroot as ext3: No such file or directory setuproot moving /dev failed:No such file or directory setuproot error mounting /proc switchroot: mount failed: /sys No such file or directory
More output, the battery failed before I could transcribe the top couple of pages though.
Andrew Gormanly wrote:
Same here, 2.6.27-0.287.rc4.git7.fc10.i686 does not boot but 2.6.27-0.244.rc4.git1.fc10.i686 is ok
Without rhgb but with quiet the messages are:
stabilized: stat /proc/bus/usb/devices: No such file or directory mount: error mounting /dev/root on /sysroot as ext3: No such file or directory setuproot: moving /dev failed: No such file or directory setuproot: error mounting /proc: No such file or directory setuproot: error mounting /sys: No such file or directory Mount failed for selinuxfs on /selinux: No such file or directory switchroot: mount failed: No such file or directory sd 0:0:0:0: [sda] Assuming drive cache: write through sd 0:0:0:0: [sda] Assuming drive cache: write through
I'll copy out the full messages from the kernel and post when I have them. This will take ages though.
Hardware is an Asus Eee PC 4G with rawhide installed on an 8GB SDHC card in the built-in reader. Fedora 9 kernels were ok as was 2.6.27-0.244.rc4.git1.fc10
2008/8/29 Andrew Gormanly a.gormanly@ucl.ac.uk:
More output, the battery failed before I could transcribe the top couple of pages though.
Andrew Gormanly wrote:
Same here, 2.6.27-0.287.rc4.git7.fc10.i686 does not boot but 2.6.27-0.244.rc4.git1.fc10.i686 is ok
Without rhgb but with quiet the messages are:
stabilized: stat /proc/bus/usb/devices: No such file or directory mount: error mounting /dev/root on /sysroot as ext3: No such file or directory setuproot: moving /dev failed: No such file or directory setuproot: error mounting /proc: No such file or directory setuproot: error mounting /sys: No such file or directory Mount failed for selinuxfs on /selinux: No such file or directory switchroot: mount failed: No such file or directory sd 0:0:0:0: [sda] Assuming drive cache: write through sd 0:0:0:0: [sda] Assuming drive cache: write through
I'll copy out the full messages from the kernel and post when I have them. This will take ages though.
Hardware is an Asus Eee PC 4G with rawhide installed on an 8GB SDHC card in the built-in reader. Fedora 9 kernels were ok as was 2.6.27-0.244.rc4.git1.fc10
-- Andrew Gormanly London Centre for Nanotechnology University College London Tel: 020 7679 3400 17-19 Gordon Street Fax: 020 7679 0595 London WC1H 0AJ a.gormanly AT ucl.ac.uk
pci 0000:00:1c.1: IO window: disabled pci 0000:00:1c.1: MEM window: 0xfbf00000-0xfbffffff pci 0000:00:1c.1: PREFETCH window: disabled pci 0000:00:1c.2: PCI bridge, secondary bus 0000:01 pci 0000:00:1c.2: IO window: disabled pci 0000:00:1c.2: MEM window: 0xf8000000-0xfbefffff pci 0000:00:1c.2: PREFETCH window: 0x000000f0000000-0x000000f6ffffff pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05 pci 0000:00:1e.0: IO window: disabled pci 0000:00:1e.0: MEM window: disabled pci 0000:00:1e.0: PREFETCH window: disabled pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 pci 0000:00:1c.0: setting latency timer to 64 pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 pci 0000:00:1c.1: setting latency timer to 64 pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 pci 0000:00:1c.2: setting latency timer to 64 pci 0000:00:1e.0: setting latency timer to 64 bus: 00 index 0 io port: [0, ffff] bus: 00 index 1 mmio: [0, ffffffffffffffff] bus: 04 index 0 mmio: [0, 0] bus: 04 index 1 mmio: [0, 0] bus: 04 index 2 mmio: [0, 0] bus: 04 index 3 mmio: [0, 0] bus: 03 index 0 mmio: [0, 0] bus: 03 index 1 mmio: [fbf00000, fbffffff] bus: 03 index 2 mmio: [0, 0] bus: 03 index 3 mmio: [0, 0] bus: 01 index 0 mmio: [0, 0] bus: 01 index 1 mmio: [f8000000, fbefffff] bus: 01 index 2 mmio: [f0000000, f6ffffff] bus: 01 index 3 mmio: [0, 0] bus: 05 index 0 mmio: [0, 0] bus: 05 index 1 mmio: [0, 0] bus: 05 index 2 mmio: [0, 0] bus: 05 index 3 io port: [0, ffff] bus: 05 index 4 mmio: [0, ffffffffffffffff] NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established has table entriesL 131072 (order: 8, 1048576 bytes) TCP bind hash table entriesL 65536 (order: 9, 2359296 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered NET: Registered protocol family 1 checking if image is initramfs... it is Switched to high resolution on CPU 0 debug: unmapping init memory f7d5e000..f7ff0000 apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) apm: overridden by ACPI audit: initializing netlink socket (disabled) type=2000 audit(1220021774.217:1): initialized highmem bounce pool size: 64 pages HugeTLB registered 4 MB page size, pre-allocated 0 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) msgmni has been set to 1704 SELinux: Registering netfilter hooks Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfg registered (default) pci 0000:00:02.0: Boot video device pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup = 0x0f30 pci 0000:00:1d.0: Performing full reset pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup = 0x0030 pci 0000:00:1d.1: Performing full reset pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup = 0x0030 pci 0000:00:1d.2: Performing full reset pci 0000:00:1d.3: uhci_check_and_reset_hc: legsup = 0x0030 pci 0000:00:1d.3: Performing full reset pcieport-driver 0000:00:1c.0: setting latency timer to 64 pcieport-driver 0000:00:1c.0: found MSI capability pci_express 0000:00:1c.0:pcie00: allocate port service pci_express 0000:00:1c.0:pcie02: allocate port service pci_express 0000:00:1c.0:pcie03: allocate port service pcieport-driver 0000:00:1c.1: setting latency timer to 64 pcieport-driver 0000:00:1c.1: found MSI capability pci_express 0000:00:1c.1:pcie00: allocate port service pci_express 0000:00:1c.1:pcie02: allocate port service pci_express 0000:00:1c.1:pcie03: allocate port service pcieport-driver 0000:00:1c.2: setting latency timer to 64 pcieport-driver 0000:00:1c.2: found MSI capability pci_express 0000:00:1c.2:pcie00: allocate port service pci_express 0000:00:1c.2:pcie02:allocate port service pci_express 0000:00:1c.2:pcie03:allocate port service pci_hotplug: PCI Hot Plug PCI Core version: 0.5 input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 ACPI: Power Button (FF) [PWRF] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1 ACPI: EC: non-query interrupt received, switching to interrupt mode ACPI: Lid Switch [LID] input: Sleep Buttion (CM) as /devices/LNXSYSTM:00/device:00/PP0C0E:00/input/input2 ACPI: Sleep Button (CM) [SLPB] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3 ACPI: Power Button (CM) [PWRB] ACPI: CPU0 (power statesL C1[C1] C2[C2] C3[C3]) processor ACPI0007:00: registered as cooling_device0 ACPI: Processor [CPU1] (supports 8 throttling states) thermal LNXTHERM:01: registered as thermal_zone0 ACPI: Thermal Zone [TZ00] (35 C) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Non-volatile memory driver v1.2 Linux agpgart interface v0.103 agpgart-intel 0000:00:00.0: Intel 915GM Chipset agpgart-intel 0000:00:00.0: detected 7932K stolen memory agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000 Serial: 8250/16550 driver4 ports, IRQ sharing enabled brd: module loaded input: Macintosh mouse button emulation as /devices/virtual/input/input4 Driver 'sd' needs updating - please use bus_type methods ehci_hcd: block sizes: qh 128 qtd 96 itd 160 sitd 96 ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 ehci_hcd 0000:00:1d.7: setting latency timer to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller drivers/usb/core/inode.c: creating file 'devices' drivers/usb/core/inode.c: creating file '001' ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1 cc=4 pcc=2 ordered !ppc ports=8 ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT ehci_hcd 0000:00:1d.7: debug port 1 ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported ehci_hcd 0000:00:1d.7: supports USB remote wakeup ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf7eb7c00 ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period-1024 RUN ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: default language 0x409 usb usb1: uevent usb usb1: usb_probe_device usb usb1: configuration #1 chosen from 1 choice usb usb1: adding 1-0:1.0 (config #1, interface 0) usb 1-0:1.0: uevent hub 1-0:1.0: usb_probe_interface hub 1-0:1.0: usb_probe_interface - got id hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected hub 1-0:1.0: standalone hub hub 1-0:1.0: no power switching (usb 1.0) hub 1-0:1.0: individual port over-current protection hub 1-0:1.0: power on to power good time: 20ms hub 1-0:1.0: local power source is good hub 1-0:1.0: trying to enable port power on non-switchable hub ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001803 POWER sig=j CSC CONNECT hub 1-0:1.0: port 5: status 0501 change 0001 hub 1-0:1.0: state 7 ports 8 chg 0020 evt 0000 drivers/usb/core/inode.c: creating file '001' hub 1-0:1.0: port 5, status 0501, change 0000, 480 Mb/s usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.27-0.287.rc4.git7.fc10.i686 ehci_hcd usb usb1: SerialNumber: 0000:00:1d.7 ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver ohci_hcd: block sizes: ed 64 td 64 USB Universal Host Controller Interface driver v3.0 uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 uhci_hcd 0000:00:1d.0: setting latency timer to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller drivers/usb/core/inode.c: creating file '002' uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.0: detected 2 ports uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000 uhci_hcd 0000:00:1d.0: Performing full reset uhci_hcd 0000:00:1d.0: supports USB remote wakeup uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e400 usb usb3: default language 0x409 usb usb3: uevent usb usb3: usb_probe_device usb usb3: configuration #1 chosen from 1 choice usb usb3: adding 2-0:1.0 (config #1, interface 0) usb 2-0:1.0: uevent hub 2-0:1.0: usb_probe_interface hub 2-0:1.0: usb_probe_interface - got id hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected hub 2-0:1.0: standalone hub hub 2-0:1.0: no power switching (usb 1.0) hub 2-0:1.0: individual port over-current protection hub 2-0:1.0: power on to power good time: 2ms hub 2-0:1.0: local power source is good hub 2-0:1.0: trying to enable port power on non-switchable hub ehci_hcd 0000:00:1d.7: port 5 high speed ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005 POWER sig=se0 PE CONNECT usb 1-5: new high speed USB device using ehci_hcd and address 2 drivers/usb/core/inode.c: creating file '001' usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: UHCI Host Controller usb usb2: Manufacturer: Linux 2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd usb usb2: SerialNumber: 0000:00:1d.0 uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 uhci_hcd 0000:00:1d.1: setting latency timer to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller drivers/usb/core/inode.c: creating file '003' uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.1: detected 2 ports uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000 uhci_hcd 0000:00:1d.1: Performing full reset uhci_hcd 0000:00:1d.1: supports USB remote wakeup uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e480 usb usb3: default language 0x409 usb usb3: uevent usb usb3: usb_probe_device usb usb3: configuration #1 chosen from 1 choice usb usb3: adding 3-0:1.0 (config #1, interface 0) usb 3-0:1.0: uevent hub 3-0:1.0: usb_probe_interface hub 3-0:1.0: usb_probe_interface - got id hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected hub 3-0:1.0: standalone hub hub 3-0:1.0: no power switching (usb 1.0) hub 3-0:1.0: individual port over-current protection hub 3-0:1.0: power on to power good time: 2ms hub 3-0:1.0: local power source is good hub 3-0:1.0: trying to enable port power on non-switchable hub ehci_hcd 0000:00:1d.7: port 5 high speed ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005 POWER sig=se0 PE CONNECT usb 1-5: default language 0x0409 usb 1-5: uevent usb 1-5: usb_probe_device usb 1-5: configuration #1 chosen from 1 choice usb 1-5: adding 1-5:1.0 (config #1, interface 0) usb 1-5:1.0: uevent drivers/usb/core/inode.c: creating file '002' usb 1-5: New USB device found, idVendor=0951, idProduct=1606 usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=4 usb 1-5: Product: UB6225 usb 1-5: Manufacturer: ENE usb 1-5: SerialNumber: 146030377350 hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000 hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 drivers/usb/core/inode.c: creating file '001' usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: UHCI Host Controller usb usb3: Manufacturer: Linux 2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd usb usb3: SerialNumber: 0000:00:1d.1 uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 uhci_hcd 0000:00:1d.2: setting latency timer to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller drivers/usb/core/inode.c: creating file '004' uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.2: detected 2 ports uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000 uhci_hcd 0000:00:1d.2: Performing full reset uhci_hcd 0000:00:1d.2: supports USB remote wakeup uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e800 usb usb4: default language 0x409 usb usb4: uevent usb usb4: usb_probe_device usb usb4: configuration #1 chosen from 1 choice usb usb4: adding 4-0:1.0 (config #1, interface 0) usb 4-0:1.0: uevent usb 4-0:1.0: usb_probe_interface usb 4-0:1.0: usb_probe_interface - got id usb 4-0:1.0: USB hub found usb 4-0:1.0: 2 ports detected usb 4-0:1.0: standalone hub usb 4-0:1.0: no power switching (usb 1.0) usb 4-0:1.0: individual port over-current protection usb 4-0:1.0: power on to power good time: 2ms usb 4-0:1.0: local power source is good usb 4-0:1.0: trying to enable port power on non-switchable hub uhci_hcd 0000:00:1d.2: port 1 portsc 0082,00 usb 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 drivers/usb/core/inode.c: creating file '001' usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: UHCI Host Controller usb usb4: Manufacturer: Linux 2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd usb usb4: SerialNumber: 0000:00:1d.2 uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 uhci_hcd 0000:00:1d.3: setting latency timer to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller drivers/usb/core/inode.c: creating file '005' uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.3: detected 2 ports uhci_hcd 0000:00:1d.3: uhci_check_and_reset_hc: cmd = 0x0000 uhci_hcd 0000:00:1d.3: Performing full reset uhci_hcd 0000:00:1d.3: supports USB remote wakeup uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e880 usb usb5: default language 0x409 usb usb5: uevent usb usb5: usb_probe_device usb usb5: configuration #1 chosen from 1 choice usb usb5: adding 5-0:1.0 (config #1, interface 0) usb 5-0:1.0: uevent usb 5-0:1.0: usb_probe_interface usb 5-0:1.0: usb_probe_interface - got id usb 5-0:1.0: USB hub found usb 5-0:1.0: 2 ports detected hub 5-0:1.0: standalone hub hub 5-0:1.0: no power switching (usb 1.0) hub 5-0:1.0: individual port over-current protection hub 5-0:1.0: power on to power good time: 2ms hub 5-0:1.0: local power source is good hub 5-0:1.0: trying to enable port power on non-switchable hub hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000 drivers/usb/core/inode.c: creating file '001' usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb5: Product: UHCI Host Controller usb usb5: Manufacturer: Linux 2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd usb usb5: SerialNumber: 0000:00:1d.3 PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 Setting up hotplug.rt at 0x60,0x64 irq 12 Creating block device nodes.on for all mice Loading ext3 module core: registered rtc_cmos as rtc0 usb usb2: suspend_rh (auto-stop)et irqs usb usb3: suspend_rh (auto-stop) Loading usb-storage modulenu Initializing USB Mass Storage driver...r hiddev usb-storage 1-5:1.0: usb_probe_interface usbhid usb-storage 1-5:1.0: usb_probe_interface - got id scsi0 : SCSI emulation for USB Mass Storage devices usbcore: registered new interface driver usb-storage USB Mass Storage support registered. Waiting for driver initialization. stabilized: stat /proc/bus/usb/devices: No such file or directory Creating root device. :941 usb-storage: device found at 207f9000..c096d000 usb-storage: waiting for device to settle before scaning Mounting root filesystem.2 keyboard as /devices/platform/i8042/serio/input/inpu mount: error mounting /dev/root on /sysroot as ext3: No such file or directory Setting up other filesystems. setuproot: moving /dev failed: No such file or directory setuproot: error mounting /proc: No such file or directory setuproot: error mounting /sys: No such file or directory Mount failed for selinuxfs on /selinux: No such file or directory Switching to new root and running init. switchroot: mount failed: No such file or directory Booting has failed. usb usb4: suspend_rh (auto-stop) Synaptics Touchpad, model: 1, fw: 6.5, id: 0x1c0b1, caps: 0xa04751/0xa00000 input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6 usb usb5: suspend_rh (auto-stop) hub 2-0:1.0: hub_suspend usb usb2: bus auto-suspend usb usb2: suspend_rh hub 3-0:1.0: hub_suspend usb usb3: bus auto-suspend usb usb3: suspend_rh hub 4-0:1.0: hub_suspend usb usb4: bus auto-suspend usb usb4: suspend_rh hub 5-0:1.0: hub_suspend usb usb5: bus auto-suspend usb usb5: suspend_rh usb-storage: device scan complete scsi 0:0:0:0: Direct-Access USB2.0 CardReader SD0 0100 PQ: 0 ANSI: 0 sd 0:0:0:0: [sda] 15954944 512-byte hardware sectors (8169 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00 sd 0:0:0:0: Assuming drive cache: write through sd 0:0:0:0: 15954944 512-byte hardware sectors (8169 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00 sd 0:0:0:0: Assuming drive cache: write through sda: sda1 sda2 sd 0:0:0:0: [sda] Attached SCSI removable disk sd 0:0:0:0: Attached SCSI generic sg0 type 0 scsi_scan_0 used greatest stack depth: 1928 bytes left
-- fedora-test-list mailing list fedora-test-list@redhat.com To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-test-list
also 287 has exactly same problem.....that means that nobody read this thread :-( and I spent some time to install and de-install the kernel.
--- On Sat, 8/30/08, Antonio M antonio.montagnani@gmail.com wrote:
From: Antonio M antonio.montagnani@gmail.com Subject: Re: kernel-2.6.27-0.284.rc4.git6.fc10.i686 doesn't boot To: "For testers of Fedora Core development releases" fedora-test-list@redhat.com Date: Saturday, August 30, 2008, 7:03 AM 2008/8/29 Andrew Gormanly a.gormanly@ucl.ac.uk:
More output, the battery failed before I could
transcribe the top couple of
pages though.
Andrew Gormanly wrote:
Same here, 2.6.27-0.287.rc4.git7.fc10.i686 does
not boot but
2.6.27-0.244.rc4.git1.fc10.i686 is ok
Without rhgb but with quiet the messages are:
stabilized: stat /proc/bus/usb/devices: No such
file or directory
mount: error mounting /dev/root on /sysroot as
ext3: No such file or
directory setuproot: moving /dev failed: No such file or
directory
setuproot: error mounting /proc: No such file or
directory
setuproot: error mounting /sys: No such file or
directory
Mount failed for selinuxfs on /selinux: No such
file or directory
switchroot: mount failed: No such file or
directory
sd 0:0:0:0: [sda] Assuming drive cache: write
through
sd 0:0:0:0: [sda] Assuming drive cache: write
through
I'll copy out the full messages from the
kernel and post when I have them.
This will take ages though.
Hardware is an Asus Eee PC 4G with rawhide
installed on an 8GB SDHC card
in the built-in reader. Fedora 9 kernels were ok
as was
2.6.27-0.244.rc4.git1.fc10
-- Andrew Gormanly London Centre for Nanotechnology University College London
Tel: 020 7679 3400
17-19 Gordon Street
Fax: 020 7679 0595
London WC1H 0AJ
a.gormanly AT ucl.ac.uk
pci 0000:00:1c.1: IO window: disabled pci 0000:00:1c.1: MEM window: 0xfbf00000-0xfbffffff pci 0000:00:1c.1: PREFETCH window: disabled pci 0000:00:1c.2: PCI bridge, secondary bus 0000:01 pci 0000:00:1c.2: IO window: disabled pci 0000:00:1c.2: MEM window: 0xf8000000-0xfbefffff pci 0000:00:1c.2: PREFETCH window:
0x000000f0000000-0x000000f6ffffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05 pci 0000:00:1e.0: IO window: disabled pci 0000:00:1e.0: MEM window: disabled pci 0000:00:1e.0: PREFETCH window: disabled pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64 pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low)
-> IRQ 17
pci 0000:00:1c.1: setting latency timer to 64 pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low)
-> IRQ 18
pci 0000:00:1c.2: setting latency timer to 64 pci 0000:00:1e.0: setting latency timer to 64 bus: 00 index 0 io port: [0, ffff] bus: 00 index 1 mmio: [0, ffffffffffffffff] bus: 04 index 0 mmio: [0, 0] bus: 04 index 1 mmio: [0, 0] bus: 04 index 2 mmio: [0, 0] bus: 04 index 3 mmio: [0, 0] bus: 03 index 0 mmio: [0, 0] bus: 03 index 1 mmio: [fbf00000, fbffffff] bus: 03 index 2 mmio: [0, 0] bus: 03 index 3 mmio: [0, 0] bus: 01 index 0 mmio: [0, 0] bus: 01 index 1 mmio: [f8000000, fbefffff] bus: 01 index 2 mmio: [f0000000, f6ffffff] bus: 01 index 3 mmio: [0, 0] bus: 05 index 0 mmio: [0, 0] bus: 05 index 1 mmio: [0, 0] bus: 05 index 2 mmio: [0, 0] bus: 05 index 3 io port: [0, ffff] bus: 05 index 4 mmio: [0, ffffffffffffffff] NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5,
131072 bytes)
TCP established has table entriesL 131072 (order: 8,
1048576 bytes)
TCP bind hash table entriesL 65536 (order: 9, 2359296
bytes)
TCP: Hash tables configured (established 131072 bind
TCP reno registered NET: Registered protocol family 1 checking if image is initramfs... it is Switched to high resolution on CPU 0 debug: unmapping init memory f7d5e000..f7ff0000 apm: BIOS version 1.2 Flags 0x03 (Driver version
1.16ac)
apm: overridden by ACPI audit: initializing netlink socket (disabled) type=2000 audit(1220021774.217:1): initialized highmem bounce pool size: 64 pages HugeTLB registered 4 MB page size, pre-allocated 0
pages
VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096
bytes)
msgmni has been set to 1704 SELinux: Registering netfilter hooks Block layer SCSI generic (bsg) driver version 0.4
loaded (major 252)
io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfg registered (default) pci 0000:00:02.0: Boot video device pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup =
0x0f30
pci 0000:00:1d.0: Performing full reset pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup =
0x0030
pci 0000:00:1d.1: Performing full reset pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup =
0x0030
pci 0000:00:1d.2: Performing full reset pci 0000:00:1d.3: uhci_check_and_reset_hc: legsup =
0x0030
pci 0000:00:1d.3: Performing full reset pcieport-driver 0000:00:1c.0: setting latency timer to
64
pcieport-driver 0000:00:1c.0: found MSI capability pci_express 0000:00:1c.0:pcie00: allocate port service pci_express 0000:00:1c.0:pcie02: allocate port service pci_express 0000:00:1c.0:pcie03: allocate port service pcieport-driver 0000:00:1c.1: setting latency timer to
64
pcieport-driver 0000:00:1c.1: found MSI capability pci_express 0000:00:1c.1:pcie00: allocate port service pci_express 0000:00:1c.1:pcie02: allocate port service pci_express 0000:00:1c.1:pcie03: allocate port service pcieport-driver 0000:00:1c.2: setting latency timer to
64
pcieport-driver 0000:00:1c.2: found MSI capability pci_express 0000:00:1c.2:pcie00: allocate port service pci_express 0000:00:1c.2:pcie02:allocate port service pci_express 0000:00:1c.2:pcie03:allocate port service pci_hotplug: PCI Hot Plug PCI Core version: 0.5 input: Power Button (FF) as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button (FF) [PWRF] input: Lid Switch as
/devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
ACPI: EC: non-query interrupt received, switching to
interrupt mode
ACPI: Lid Switch [LID] input: Sleep Buttion (CM) as /devices/LNXSYSTM:00/device:00/PP0C0E:00/input/input2 ACPI: Sleep Button (CM) [SLPB] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3 ACPI: Power Button (CM) [PWRB] ACPI: CPU0 (power statesL C1[C1] C2[C2] C3[C3]) processor ACPI0007:00: registered as cooling_device0 ACPI: Processor [CPU1] (supports 8 throttling states) thermal LNXTHERM:01: registered as thermal_zone0 ACPI: Thermal Zone [TZ00] (35 C) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Non-volatile memory driver v1.2 Linux agpgart interface v0.103 agpgart-intel 0000:00:00.0: Intel 915GM Chipset agpgart-intel 0000:00:00.0: detected 7932K stolen
memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @
0xd0000000
Serial: 8250/16550 driver4 ports, IRQ sharing enabled brd: module loaded input: Macintosh mouse button emulation as
/devices/virtual/input/input4
Driver 'sd' needs updating - please use
bus_type methods
ehci_hcd: block sizes: qh 128 qtd 96 itd 160 sitd 96 ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level,
low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller drivers/usb/core/inode.c: creating file
'devices'
drivers/usb/core/inode.c: creating file '001' ehci_hcd 0000:00:1d.7: new USB bus registered,
assigned bus number 1
ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1
cc=4 pcc=2 ordered
!ppc ports=8 ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7
uframes 1024 64 bit
addr ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0
ithresh=8 period=1024
Reset HALT ehci_hcd 0000:00:1d.7: debug port 1 ehci_hcd 0000:00:1d.7: cache line size of 32 is not
supported
ehci_hcd 0000:00:1d.7: supports USB remote wakeup ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf7eb7c00 ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0
ithresh=8 period=1024
Reset HALT ehci_hcd 0000:00:1d.7: init command 010001 (park)=0
ithresh=1 period-1024
RUN ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00,
driver 10 Dec 2004
usb usb1: default language 0x409 usb usb1: uevent usb usb1: usb_probe_device usb usb1: configuration #1 chosen from 1 choice usb usb1: adding 1-0:1.0 (config #1, interface 0) usb 1-0:1.0: uevent hub 1-0:1.0: usb_probe_interface hub 1-0:1.0: usb_probe_interface - got id hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected hub 1-0:1.0: standalone hub hub 1-0:1.0: no power switching (usb 1.0) hub 1-0:1.0: individual port over-current protection hub 1-0:1.0: power on to power good time: 20ms hub 1-0:1.0: local power source is good hub 1-0:1.0: trying to enable port power on
non-switchable hub
ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001803
POWER sig=j CSC
CONNECT hub 1-0:1.0: port 5: status 0501 change 0001 hub 1-0:1.0: state 7 ports 8 chg 0020 evt 0000 drivers/usb/core/inode.c: creating file '001' hub 1-0:1.0: port 5, status 0501, change 0000, 480
Mb/s
usb usb1: New USB device found, idVendor=1d6b,
idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux
2.6.27-0.287.rc4.git7.fc10.i686 ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7 ohci_hcd: 2006 August 04 USB 1.1 'Open' Host
Controller (OHCI) Driver
ohci_hcd: block sizes: ed 64 td 64 USB Universal Host Controller Interface driver v3.0 uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level,
low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller drivers/usb/core/inode.c: creating file '002' uhci_hcd 0000:00:1d.0: new USB bus registered,
assigned bus number 2
uhci_hcd 0000:00:1d.0: detected 2 ports uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd =
0x0000
uhci_hcd 0000:00:1d.0: Performing full reset uhci_hcd 0000:00:1d.0: supports USB remote wakeup uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e400 usb usb3: default language 0x409 usb usb3: uevent usb usb3: usb_probe_device usb usb3: configuration #1 chosen from 1 choice usb usb3: adding 2-0:1.0 (config #1, interface 0) usb 2-0:1.0: uevent hub 2-0:1.0: usb_probe_interface hub 2-0:1.0: usb_probe_interface - got id hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected hub 2-0:1.0: standalone hub hub 2-0:1.0: no power switching (usb 1.0) hub 2-0:1.0: individual port over-current protection hub 2-0:1.0: power on to power good time: 2ms hub 2-0:1.0: local power source is good hub 2-0:1.0: trying to enable port power on
non-switchable hub
ehci_hcd 0000:00:1d.7: port 5 high speed ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005
POWER sig=se0 PE
CONNECT usb 1-5: new high speed USB device using ehci_hcd and
address 2
drivers/usb/core/inode.c: creating file '001' usb usb2: New USB device found, idVendor=1d6b,
idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
usb usb2: Product: UHCI Host Controller usb usb2: Manufacturer: Linux
2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0 uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level,
low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller drivers/usb/core/inode.c: creating file '003' uhci_hcd 0000:00:1d.1: new USB bus registered,
assigned bus number 3
uhci_hcd 0000:00:1d.1: detected 2 ports uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd =
0x0000
uhci_hcd 0000:00:1d.1: Performing full reset uhci_hcd 0000:00:1d.1: supports USB remote wakeup uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e480 usb usb3: default language 0x409 usb usb3: uevent usb usb3: usb_probe_device usb usb3: configuration #1 chosen from 1 choice usb usb3: adding 3-0:1.0 (config #1, interface 0) usb 3-0:1.0: uevent hub 3-0:1.0: usb_probe_interface hub 3-0:1.0: usb_probe_interface - got id hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected hub 3-0:1.0: standalone hub hub 3-0:1.0: no power switching (usb 1.0) hub 3-0:1.0: individual port over-current protection hub 3-0:1.0: power on to power good time: 2ms hub 3-0:1.0: local power source is good hub 3-0:1.0: trying to enable port power on
non-switchable hub
ehci_hcd 0000:00:1d.7: port 5 high speed ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005
POWER sig=se0 PE
CONNECT usb 1-5: default language 0x0409 usb 1-5: uevent usb 1-5: usb_probe_device usb 1-5: configuration #1 chosen from 1 choice usb 1-5: adding 1-5:1.0 (config #1, interface 0) usb 1-5:1.0: uevent drivers/usb/core/inode.c: creating file '002' usb 1-5: New USB device found, idVendor=0951,
idProduct=1606
usb 1-5: New USB device strings: Mfr=1, Product=2,
SerialNumber=4
usb 1-5: Product: UB6225 usb 1-5: Manufacturer: ENE usb 1-5: SerialNumber: 146030377350 hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000 hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 drivers/usb/core/inode.c: creating file '001' usb usb3: New USB device found, idVendor=1d6b,
idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
usb usb3: Product: UHCI Host Controller usb usb3: Manufacturer: Linux
2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1 uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level,
low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller drivers/usb/core/inode.c: creating file '004' uhci_hcd 0000:00:1d.2: new USB bus registered,
assigned bus number 4
uhci_hcd 0000:00:1d.2: detected 2 ports uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd =
0x0000
uhci_hcd 0000:00:1d.2: Performing full reset uhci_hcd 0000:00:1d.2: supports USB remote wakeup uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e800 usb usb4: default language 0x409 usb usb4: uevent usb usb4: usb_probe_device usb usb4: configuration #1 chosen from 1 choice usb usb4: adding 4-0:1.0 (config #1, interface 0) usb 4-0:1.0: uevent usb 4-0:1.0: usb_probe_interface usb 4-0:1.0: usb_probe_interface - got id usb 4-0:1.0: USB hub found usb 4-0:1.0: 2 ports detected usb 4-0:1.0: standalone hub usb 4-0:1.0: no power switching (usb 1.0) usb 4-0:1.0: individual port over-current protection usb 4-0:1.0: power on to power good time: 2ms usb 4-0:1.0: local power source is good usb 4-0:1.0: trying to enable port power on
non-switchable hub
uhci_hcd 0000:00:1d.2: port 1 portsc 0082,00 usb 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 drivers/usb/core/inode.c: creating file '001' usb usb4: New USB device found, idVendor=1d6b,
idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
usb usb4: Product: UHCI Host Controller usb usb4: Manufacturer: Linux
2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2 uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level,
low) -> IRQ 16
uhci_hcd 0000:00:1d.3: setting latency timer to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller drivers/usb/core/inode.c: creating file '005' uhci_hcd 0000:00:1d.3: new USB bus registered,
assigned bus number 5
uhci_hcd 0000:00:1d.3: detected 2 ports uhci_hcd 0000:00:1d.3: uhci_check_and_reset_hc: cmd =
0x0000
uhci_hcd 0000:00:1d.3: Performing full reset uhci_hcd 0000:00:1d.3: supports USB remote wakeup uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e880 usb usb5: default language 0x409 usb usb5: uevent usb usb5: usb_probe_device usb usb5: configuration #1 chosen from 1 choice usb usb5: adding 5-0:1.0 (config #1, interface 0) usb 5-0:1.0: uevent usb 5-0:1.0: usb_probe_interface usb 5-0:1.0: usb_probe_interface - got id usb 5-0:1.0: USB hub found usb 5-0:1.0: 2 ports detected hub 5-0:1.0: standalone hub hub 5-0:1.0: no power switching (usb 1.0) hub 5-0:1.0: individual port over-current protection hub 5-0:1.0: power on to power good time: 2ms hub 5-0:1.0: local power source is good hub 5-0:1.0: trying to enable port power on
non-switchable hub
hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000 drivers/usb/core/inode.c: creating file '001' usb usb5: New USB device found, idVendor=1d6b,
idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
usb usb5: Product: UHCI Host Controller usb usb5: Manufacturer: Linux
2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.3 PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at
0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1 Setting up hotplug.rt at 0x60,0x64 irq 12 Creating block device nodes.on for all mice Loading ext3 module core: registered rtc_cmos as rtc0 usb usb2: suspend_rh (auto-stop)et irqs usb usb3: suspend_rh (auto-stop) Loading usb-storage modulenu Initializing USB Mass Storage driver...r hiddev usb-storage 1-5:1.0: usb_probe_interface usbhid usb-storage 1-5:1.0: usb_probe_interface - got id scsi0 : SCSI emulation for USB Mass Storage devices usbcore: registered new interface driver usb-storage USB Mass Storage support registered. Waiting for driver initialization. stabilized: stat /proc/bus/usb/devices: No such file
or directory
Creating root device. :941 usb-storage: device found at 207f9000..c096d000 usb-storage: waiting for device to settle before
scaning
Mounting root filesystem.2 keyboard as /devices/platform/i8042/serio/input/inpu mount: error mounting /dev/root on /sysroot as ext3:
No such file or
directory Setting up other filesystems. setuproot: moving /dev failed: No such file or
directory
setuproot: error mounting /proc: No such file or
directory
setuproot: error mounting /sys: No such file or
directory
Mount failed for selinuxfs on /selinux: No such file
or directory
Switching to new root and running init. switchroot: mount failed: No such file or directory Booting has failed. usb usb4: suspend_rh (auto-stop) Synaptics Touchpad, model: 1, fw: 6.5, id: 0x1c0b1,
caps: 0xa04751/0xa00000
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6 usb usb5: suspend_rh (auto-stop) hub 2-0:1.0: hub_suspend usb usb2: bus auto-suspend usb usb2: suspend_rh hub 3-0:1.0: hub_suspend usb usb3: bus auto-suspend usb usb3: suspend_rh hub 4-0:1.0: hub_suspend usb usb4: bus auto-suspend usb usb4: suspend_rh hub 5-0:1.0: hub_suspend usb usb5: bus auto-suspend usb usb5: suspend_rh usb-storage: device scan complete scsi 0:0:0:0: Direct-Access USB2.0 CardReader
SD0 0100 PQ: 0 ANSI: 0
sd 0:0:0:0: [sda] 15954944 512-byte hardware sectors
(8169 MB)
sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00 sd 0:0:0:0: Assuming drive cache: write through sd 0:0:0:0: 15954944 512-byte hardware sectors (8169
MB)
sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00 sd 0:0:0:0: Assuming drive cache: write through sda: sda1 sda2 sd 0:0:0:0: [sda] Attached SCSI removable disk sd 0:0:0:0: Attached SCSI generic sg0 type 0 scsi_scan_0 used greatest stack depth: 1928 bytes left
-- fedora-test-list mailing list fedora-test-list@redhat.com To unsubscribe:
https://www.redhat.com/mailman/listinfo/fedora-test-list
also 287 has exactly same problem.....that means that nobody read this thread :-( and I spent some time to install and de-install the kernel.
It happens at some point or another. I installed the 284 kernel and it worked for me. However I even installed the 290 kernel and it worked! Things like this happen to us at one point or another. I have also needed to remove several kernels that were not working for me :)
BTW, thank you for bringing up the printing problem. I am having problems printing as well. We are here and we do read the thread(s). Sorry I could not have provided advice since those kernels booted for me :(
-- Antonio Montagnani Skype : antoniomontag
--
Regards,
Antonio
2008/8/30 Antonio Olivares olivares14031@yahoo.com:
--- On Sat, 8/30/08, Antonio M antonio.montagnani@gmail.com wrote:
From: Antonio M antonio.montagnani@gmail.com Subject: Re: kernel-2.6.27-0.284.rc4.git6.fc10.i686 doesn't boot To: "For testers of Fedora Core development releases" fedora-test-list@redhat.com Date: Saturday, August 30, 2008, 7:03 AM 2008/8/29 Andrew Gormanly a.gormanly@ucl.ac.uk:
More output, the battery failed before I could
transcribe the top couple of
pages though.
Andrew Gormanly wrote:
Same here, 2.6.27-0.287.rc4.git7.fc10.i686 does
not boot but
2.6.27-0.244.rc4.git1.fc10.i686 is ok
Without rhgb but with quiet the messages are:
stabilized: stat /proc/bus/usb/devices: No such
file or directory
mount: error mounting /dev/root on /sysroot as
ext3: No such file or
directory setuproot: moving /dev failed: No such file or
directory
setuproot: error mounting /proc: No such file or
directory
setuproot: error mounting /sys: No such file or
directory
Mount failed for selinuxfs on /selinux: No such
file or directory
switchroot: mount failed: No such file or
directory
sd 0:0:0:0: [sda] Assuming drive cache: write
through
sd 0:0:0:0: [sda] Assuming drive cache: write
through
I'll copy out the full messages from the
kernel and post when I have them.
This will take ages though.
Hardware is an Asus Eee PC 4G with rawhide
installed on an 8GB SDHC card
in the built-in reader. Fedora 9 kernels were ok
as was
2.6.27-0.244.rc4.git1.fc10
-- Andrew Gormanly London Centre for Nanotechnology University College London
Tel: 020 7679 3400
17-19 Gordon Street
Fax: 020 7679 0595
London WC1H 0AJ
a.gormanly AT ucl.ac.uk
pci 0000:00:1c.1: IO window: disabled pci 0000:00:1c.1: MEM window: 0xfbf00000-0xfbffffff pci 0000:00:1c.1: PREFETCH window: disabled pci 0000:00:1c.2: PCI bridge, secondary bus 0000:01 pci 0000:00:1c.2: IO window: disabled pci 0000:00:1c.2: MEM window: 0xf8000000-0xfbefffff pci 0000:00:1c.2: PREFETCH window:
0x000000f0000000-0x000000f6ffffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05 pci 0000:00:1e.0: IO window: disabled pci 0000:00:1e.0: MEM window: disabled pci 0000:00:1e.0: PREFETCH window: disabled pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64 pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low)
-> IRQ 17
pci 0000:00:1c.1: setting latency timer to 64 pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low)
-> IRQ 18
pci 0000:00:1c.2: setting latency timer to 64 pci 0000:00:1e.0: setting latency timer to 64 bus: 00 index 0 io port: [0, ffff] bus: 00 index 1 mmio: [0, ffffffffffffffff] bus: 04 index 0 mmio: [0, 0] bus: 04 index 1 mmio: [0, 0] bus: 04 index 2 mmio: [0, 0] bus: 04 index 3 mmio: [0, 0] bus: 03 index 0 mmio: [0, 0] bus: 03 index 1 mmio: [fbf00000, fbffffff] bus: 03 index 2 mmio: [0, 0] bus: 03 index 3 mmio: [0, 0] bus: 01 index 0 mmio: [0, 0] bus: 01 index 1 mmio: [f8000000, fbefffff] bus: 01 index 2 mmio: [f0000000, f6ffffff] bus: 01 index 3 mmio: [0, 0] bus: 05 index 0 mmio: [0, 0] bus: 05 index 1 mmio: [0, 0] bus: 05 index 2 mmio: [0, 0] bus: 05 index 3 io port: [0, ffff] bus: 05 index 4 mmio: [0, ffffffffffffffff] NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5,
131072 bytes)
TCP established has table entriesL 131072 (order: 8,
1048576 bytes)
TCP bind hash table entriesL 65536 (order: 9, 2359296
bytes)
TCP: Hash tables configured (established 131072 bind
TCP reno registered NET: Registered protocol family 1 checking if image is initramfs... it is Switched to high resolution on CPU 0 debug: unmapping init memory f7d5e000..f7ff0000 apm: BIOS version 1.2 Flags 0x03 (Driver version
1.16ac)
apm: overridden by ACPI audit: initializing netlink socket (disabled) type=2000 audit(1220021774.217:1): initialized highmem bounce pool size: 64 pages HugeTLB registered 4 MB page size, pre-allocated 0
pages
VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096
bytes)
msgmni has been set to 1704 SELinux: Registering netfilter hooks Block layer SCSI generic (bsg) driver version 0.4
loaded (major 252)
io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfg registered (default) pci 0000:00:02.0: Boot video device pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup =
0x0f30
pci 0000:00:1d.0: Performing full reset pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup =
0x0030
pci 0000:00:1d.1: Performing full reset pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup =
0x0030
pci 0000:00:1d.2: Performing full reset pci 0000:00:1d.3: uhci_check_and_reset_hc: legsup =
0x0030
pci 0000:00:1d.3: Performing full reset pcieport-driver 0000:00:1c.0: setting latency timer to
64
pcieport-driver 0000:00:1c.0: found MSI capability pci_express 0000:00:1c.0:pcie00: allocate port service pci_express 0000:00:1c.0:pcie02: allocate port service pci_express 0000:00:1c.0:pcie03: allocate port service pcieport-driver 0000:00:1c.1: setting latency timer to
64
pcieport-driver 0000:00:1c.1: found MSI capability pci_express 0000:00:1c.1:pcie00: allocate port service pci_express 0000:00:1c.1:pcie02: allocate port service pci_express 0000:00:1c.1:pcie03: allocate port service pcieport-driver 0000:00:1c.2: setting latency timer to
64
pcieport-driver 0000:00:1c.2: found MSI capability pci_express 0000:00:1c.2:pcie00: allocate port service pci_express 0000:00:1c.2:pcie02:allocate port service pci_express 0000:00:1c.2:pcie03:allocate port service pci_hotplug: PCI Hot Plug PCI Core version: 0.5 input: Power Button (FF) as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button (FF) [PWRF] input: Lid Switch as
/devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
ACPI: EC: non-query interrupt received, switching to
interrupt mode
ACPI: Lid Switch [LID] input: Sleep Buttion (CM) as /devices/LNXSYSTM:00/device:00/PP0C0E:00/input/input2 ACPI: Sleep Button (CM) [SLPB] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3 ACPI: Power Button (CM) [PWRB] ACPI: CPU0 (power statesL C1[C1] C2[C2] C3[C3]) processor ACPI0007:00: registered as cooling_device0 ACPI: Processor [CPU1] (supports 8 throttling states) thermal LNXTHERM:01: registered as thermal_zone0 ACPI: Thermal Zone [TZ00] (35 C) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Non-volatile memory driver v1.2 Linux agpgart interface v0.103 agpgart-intel 0000:00:00.0: Intel 915GM Chipset agpgart-intel 0000:00:00.0: detected 7932K stolen
memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @
0xd0000000
Serial: 8250/16550 driver4 ports, IRQ sharing enabled brd: module loaded input: Macintosh mouse button emulation as
/devices/virtual/input/input4
Driver 'sd' needs updating - please use
bus_type methods
ehci_hcd: block sizes: qh 128 qtd 96 itd 160 sitd 96 ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level,
low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller drivers/usb/core/inode.c: creating file
'devices'
drivers/usb/core/inode.c: creating file '001' ehci_hcd 0000:00:1d.7: new USB bus registered,
assigned bus number 1
ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1
cc=4 pcc=2 ordered
!ppc ports=8 ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7
uframes 1024 64 bit
addr ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0
ithresh=8 period=1024
Reset HALT ehci_hcd 0000:00:1d.7: debug port 1 ehci_hcd 0000:00:1d.7: cache line size of 32 is not
supported
ehci_hcd 0000:00:1d.7: supports USB remote wakeup ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf7eb7c00 ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0
ithresh=8 period=1024
Reset HALT ehci_hcd 0000:00:1d.7: init command 010001 (park)=0
ithresh=1 period-1024
RUN ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00,
driver 10 Dec 2004
usb usb1: default language 0x409 usb usb1: uevent usb usb1: usb_probe_device usb usb1: configuration #1 chosen from 1 choice usb usb1: adding 1-0:1.0 (config #1, interface 0) usb 1-0:1.0: uevent hub 1-0:1.0: usb_probe_interface hub 1-0:1.0: usb_probe_interface - got id hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected hub 1-0:1.0: standalone hub hub 1-0:1.0: no power switching (usb 1.0) hub 1-0:1.0: individual port over-current protection hub 1-0:1.0: power on to power good time: 20ms hub 1-0:1.0: local power source is good hub 1-0:1.0: trying to enable port power on
non-switchable hub
ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001803
POWER sig=j CSC
CONNECT hub 1-0:1.0: port 5: status 0501 change 0001 hub 1-0:1.0: state 7 ports 8 chg 0020 evt 0000 drivers/usb/core/inode.c: creating file '001' hub 1-0:1.0: port 5, status 0501, change 0000, 480
Mb/s
usb usb1: New USB device found, idVendor=1d6b,
idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux
2.6.27-0.287.rc4.git7.fc10.i686 ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7 ohci_hcd: 2006 August 04 USB 1.1 'Open' Host
Controller (OHCI) Driver
ohci_hcd: block sizes: ed 64 td 64 USB Universal Host Controller Interface driver v3.0 uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level,
low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller drivers/usb/core/inode.c: creating file '002' uhci_hcd 0000:00:1d.0: new USB bus registered,
assigned bus number 2
uhci_hcd 0000:00:1d.0: detected 2 ports uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd =
0x0000
uhci_hcd 0000:00:1d.0: Performing full reset uhci_hcd 0000:00:1d.0: supports USB remote wakeup uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e400 usb usb3: default language 0x409 usb usb3: uevent usb usb3: usb_probe_device usb usb3: configuration #1 chosen from 1 choice usb usb3: adding 2-0:1.0 (config #1, interface 0) usb 2-0:1.0: uevent hub 2-0:1.0: usb_probe_interface hub 2-0:1.0: usb_probe_interface - got id hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected hub 2-0:1.0: standalone hub hub 2-0:1.0: no power switching (usb 1.0) hub 2-0:1.0: individual port over-current protection hub 2-0:1.0: power on to power good time: 2ms hub 2-0:1.0: local power source is good hub 2-0:1.0: trying to enable port power on
non-switchable hub
ehci_hcd 0000:00:1d.7: port 5 high speed ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005
POWER sig=se0 PE
CONNECT usb 1-5: new high speed USB device using ehci_hcd and
address 2
drivers/usb/core/inode.c: creating file '001' usb usb2: New USB device found, idVendor=1d6b,
idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
usb usb2: Product: UHCI Host Controller usb usb2: Manufacturer: Linux
2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0 uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level,
low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller drivers/usb/core/inode.c: creating file '003' uhci_hcd 0000:00:1d.1: new USB bus registered,
assigned bus number 3
uhci_hcd 0000:00:1d.1: detected 2 ports uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd =
0x0000
uhci_hcd 0000:00:1d.1: Performing full reset uhci_hcd 0000:00:1d.1: supports USB remote wakeup uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e480 usb usb3: default language 0x409 usb usb3: uevent usb usb3: usb_probe_device usb usb3: configuration #1 chosen from 1 choice usb usb3: adding 3-0:1.0 (config #1, interface 0) usb 3-0:1.0: uevent hub 3-0:1.0: usb_probe_interface hub 3-0:1.0: usb_probe_interface - got id hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected hub 3-0:1.0: standalone hub hub 3-0:1.0: no power switching (usb 1.0) hub 3-0:1.0: individual port over-current protection hub 3-0:1.0: power on to power good time: 2ms hub 3-0:1.0: local power source is good hub 3-0:1.0: trying to enable port power on
non-switchable hub
ehci_hcd 0000:00:1d.7: port 5 high speed ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005
POWER sig=se0 PE
CONNECT usb 1-5: default language 0x0409 usb 1-5: uevent usb 1-5: usb_probe_device usb 1-5: configuration #1 chosen from 1 choice usb 1-5: adding 1-5:1.0 (config #1, interface 0) usb 1-5:1.0: uevent drivers/usb/core/inode.c: creating file '002' usb 1-5: New USB device found, idVendor=0951,
idProduct=1606
usb 1-5: New USB device strings: Mfr=1, Product=2,
SerialNumber=4
usb 1-5: Product: UB6225 usb 1-5: Manufacturer: ENE usb 1-5: SerialNumber: 146030377350 hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000 hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 drivers/usb/core/inode.c: creating file '001' usb usb3: New USB device found, idVendor=1d6b,
idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
usb usb3: Product: UHCI Host Controller usb usb3: Manufacturer: Linux
2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1 uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level,
low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller drivers/usb/core/inode.c: creating file '004' uhci_hcd 0000:00:1d.2: new USB bus registered,
assigned bus number 4
uhci_hcd 0000:00:1d.2: detected 2 ports uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd =
0x0000
uhci_hcd 0000:00:1d.2: Performing full reset uhci_hcd 0000:00:1d.2: supports USB remote wakeup uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e800 usb usb4: default language 0x409 usb usb4: uevent usb usb4: usb_probe_device usb usb4: configuration #1 chosen from 1 choice usb usb4: adding 4-0:1.0 (config #1, interface 0) usb 4-0:1.0: uevent usb 4-0:1.0: usb_probe_interface usb 4-0:1.0: usb_probe_interface - got id usb 4-0:1.0: USB hub found usb 4-0:1.0: 2 ports detected usb 4-0:1.0: standalone hub usb 4-0:1.0: no power switching (usb 1.0) usb 4-0:1.0: individual port over-current protection usb 4-0:1.0: power on to power good time: 2ms usb 4-0:1.0: local power source is good usb 4-0:1.0: trying to enable port power on
non-switchable hub
uhci_hcd 0000:00:1d.2: port 1 portsc 0082,00 usb 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 drivers/usb/core/inode.c: creating file '001' usb usb4: New USB device found, idVendor=1d6b,
idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
usb usb4: Product: UHCI Host Controller usb usb4: Manufacturer: Linux
2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2 uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level,
low) -> IRQ 16
uhci_hcd 0000:00:1d.3: setting latency timer to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller drivers/usb/core/inode.c: creating file '005' uhci_hcd 0000:00:1d.3: new USB bus registered,
assigned bus number 5
uhci_hcd 0000:00:1d.3: detected 2 ports uhci_hcd 0000:00:1d.3: uhci_check_and_reset_hc: cmd =
0x0000
uhci_hcd 0000:00:1d.3: Performing full reset uhci_hcd 0000:00:1d.3: supports USB remote wakeup uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e880 usb usb5: default language 0x409 usb usb5: uevent usb usb5: usb_probe_device usb usb5: configuration #1 chosen from 1 choice usb usb5: adding 5-0:1.0 (config #1, interface 0) usb 5-0:1.0: uevent usb 5-0:1.0: usb_probe_interface usb 5-0:1.0: usb_probe_interface - got id usb 5-0:1.0: USB hub found usb 5-0:1.0: 2 ports detected hub 5-0:1.0: standalone hub hub 5-0:1.0: no power switching (usb 1.0) hub 5-0:1.0: individual port over-current protection hub 5-0:1.0: power on to power good time: 2ms hub 5-0:1.0: local power source is good hub 5-0:1.0: trying to enable port power on
non-switchable hub
hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000 drivers/usb/core/inode.c: creating file '001' usb usb5: New USB device found, idVendor=1d6b,
idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
usb usb5: Product: UHCI Host Controller usb usb5: Manufacturer: Linux
2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.3 PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at
0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1 Setting up hotplug.rt at 0x60,0x64 irq 12 Creating block device nodes.on for all mice Loading ext3 module core: registered rtc_cmos as rtc0 usb usb2: suspend_rh (auto-stop)et irqs usb usb3: suspend_rh (auto-stop) Loading usb-storage modulenu Initializing USB Mass Storage driver...r hiddev usb-storage 1-5:1.0: usb_probe_interface usbhid usb-storage 1-5:1.0: usb_probe_interface - got id scsi0 : SCSI emulation for USB Mass Storage devices usbcore: registered new interface driver usb-storage USB Mass Storage support registered. Waiting for driver initialization. stabilized: stat /proc/bus/usb/devices: No such file
or directory
Creating root device. :941 usb-storage: device found at 207f9000..c096d000 usb-storage: waiting for device to settle before
scaning
Mounting root filesystem.2 keyboard as /devices/platform/i8042/serio/input/inpu mount: error mounting /dev/root on /sysroot as ext3:
No such file or
directory Setting up other filesystems. setuproot: moving /dev failed: No such file or
directory
setuproot: error mounting /proc: No such file or
directory
setuproot: error mounting /sys: No such file or
directory
Mount failed for selinuxfs on /selinux: No such file
or directory
Switching to new root and running init. switchroot: mount failed: No such file or directory Booting has failed. usb usb4: suspend_rh (auto-stop) Synaptics Touchpad, model: 1, fw: 6.5, id: 0x1c0b1,
caps: 0xa04751/0xa00000
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6 usb usb5: suspend_rh (auto-stop) hub 2-0:1.0: hub_suspend usb usb2: bus auto-suspend usb usb2: suspend_rh hub 3-0:1.0: hub_suspend usb usb3: bus auto-suspend usb usb3: suspend_rh hub 4-0:1.0: hub_suspend usb usb4: bus auto-suspend usb usb4: suspend_rh hub 5-0:1.0: hub_suspend usb usb5: bus auto-suspend usb usb5: suspend_rh usb-storage: device scan complete scsi 0:0:0:0: Direct-Access USB2.0 CardReader
SD0 0100 PQ: 0 ANSI: 0
sd 0:0:0:0: [sda] 15954944 512-byte hardware sectors
(8169 MB)
sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00 sd 0:0:0:0: Assuming drive cache: write through sd 0:0:0:0: 15954944 512-byte hardware sectors (8169
MB)
sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00 sd 0:0:0:0: Assuming drive cache: write through sda: sda1 sda2 sd 0:0:0:0: [sda] Attached SCSI removable disk sd 0:0:0:0: Attached SCSI generic sg0 type 0 scsi_scan_0 used greatest stack depth: 1928 bytes left
-- fedora-test-list mailing list fedora-test-list@redhat.com To unsubscribe:
https://www.redhat.com/mailman/listinfo/fedora-test-list
also 287 has exactly same problem.....that means that nobody read this thread :-( and I spent some time to install and de-install the kernel.
It happens at some point or another. I installed the 284 kernel and it worked for me. However I even installed the 290 kernel and it worked! Things like this happen to us at one point or another. I have also needed to remove several kernels that were not working for me :)
BTW, thank you for bringing up the printing problem. I am having problems printing as well. We are here and we do read the thread(s). Sorry I could not have provided advice since those kernels booted for me :(
-- Antonio Montagnani Skype : antoniomontag
--
Regards,
Antonio
-- fedora-test-list mailing list fedora-test-list@redhat.com To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-test-list
even kernel-2.6.27-0.290.rc5.fc10.i686 is not booting off my USB HD drive, with same problems of other two kernels. Latest kernel booting off an USB HD drive is kernel-2.6.27-0.244.rc2.git1.fc10.i686.
2008/8/31 Antonio M antonio.montagnani@gmail.com:
2008/8/30 Antonio Olivares olivares14031@yahoo.com:
--- On Sat, 8/30/08, Antonio M antonio.montagnani@gmail.com wrote:
From: Antonio M antonio.montagnani@gmail.com Subject: Re: kernel-2.6.27-0.284.rc4.git6.fc10.i686 doesn't boot To: "For testers of Fedora Core development releases" <
fedora-test-list@redhat.com>
Date: Saturday, August 30, 2008, 7:03 AM 2008/8/29 Andrew Gormanly a.gormanly@ucl.ac.uk:
More output, the battery failed before I could
transcribe the top couple of
pages though.
Andrew Gormanly wrote:
Same here, 2.6.27-0.287.rc4.git7.fc10.i686 does
not boot but
2.6.27-0.244.rc4.git1.fc10.i686 is ok
Without rhgb but with quiet the messages are:
stabilized: stat /proc/bus/usb/devices: No such
file or directory
mount: error mounting /dev/root on /sysroot as
ext3: No such file or
directory setuproot: moving /dev failed: No such file or
directory
setuproot: error mounting /proc: No such file or
directory
setuproot: error mounting /sys: No such file or
directory
Mount failed for selinuxfs on /selinux: No such
file or directory
switchroot: mount failed: No such file or
directory
sd 0:0:0:0: [sda] Assuming drive cache: write
through
sd 0:0:0:0: [sda] Assuming drive cache: write
through
I'll copy out the full messages from the
kernel and post when I have them.
This will take ages though.
Hardware is an Asus Eee PC 4G with rawhide
installed on an 8GB SDHC card
in the built-in reader. Fedora 9 kernels were ok
as was
2.6.27-0.244.rc4.git1.fc10
-- Andrew Gormanly London Centre for Nanotechnology University College London
Tel: 020 7679 3400
17-19 Gordon Street
Fax: 020 7679 0595
London WC1H 0AJ
a.gormanly AT ucl.ac.uk
pci 0000:00:1c.1: IO window: disabled pci 0000:00:1c.1: MEM window: 0xfbf00000-0xfbffffff pci 0000:00:1c.1: PREFETCH window: disabled pci 0000:00:1c.2: PCI bridge, secondary bus 0000:01 pci 0000:00:1c.2: IO window: disabled pci 0000:00:1c.2: MEM window: 0xf8000000-0xfbefffff pci 0000:00:1c.2: PREFETCH window:
0x000000f0000000-0x000000f6ffffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05 pci 0000:00:1e.0: IO window: disabled pci 0000:00:1e.0: MEM window: disabled pci 0000:00:1e.0: PREFETCH window: disabled pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low)
-> IRQ 16
pci 0000:00:1c.0: setting latency timer to 64 pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low)
-> IRQ 17
pci 0000:00:1c.1: setting latency timer to 64 pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low)
-> IRQ 18
pci 0000:00:1c.2: setting latency timer to 64 pci 0000:00:1e.0: setting latency timer to 64 bus: 00 index 0 io port: [0, ffff] bus: 00 index 1 mmio: [0, ffffffffffffffff] bus: 04 index 0 mmio: [0, 0] bus: 04 index 1 mmio: [0, 0] bus: 04 index 2 mmio: [0, 0] bus: 04 index 3 mmio: [0, 0] bus: 03 index 0 mmio: [0, 0] bus: 03 index 1 mmio: [fbf00000, fbffffff] bus: 03 index 2 mmio: [0, 0] bus: 03 index 3 mmio: [0, 0] bus: 01 index 0 mmio: [0, 0] bus: 01 index 1 mmio: [f8000000, fbefffff] bus: 01 index 2 mmio: [f0000000, f6ffffff] bus: 01 index 3 mmio: [0, 0] bus: 05 index 0 mmio: [0, 0] bus: 05 index 1 mmio: [0, 0] bus: 05 index 2 mmio: [0, 0] bus: 05 index 3 io port: [0, ffff] bus: 05 index 4 mmio: [0, ffffffffffffffff] NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5,
131072 bytes)
TCP established has table entriesL 131072 (order: 8,
1048576 bytes)
TCP bind hash table entriesL 65536 (order: 9, 2359296
bytes)
TCP: Hash tables configured (established 131072 bind
TCP reno registered NET: Registered protocol family 1 checking if image is initramfs... it is Switched to high resolution on CPU 0 debug: unmapping init memory f7d5e000..f7ff0000 apm: BIOS version 1.2 Flags 0x03 (Driver version
1.16ac)
apm: overridden by ACPI audit: initializing netlink socket (disabled) type=2000 audit(1220021774.217:1): initialized highmem bounce pool size: 64 pages HugeTLB registered 4 MB page size, pre-allocated 0
pages
VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096
bytes)
msgmni has been set to 1704 SELinux: Registering netfilter hooks Block layer SCSI generic (bsg) driver version 0.4
loaded (major 252)
io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfg registered (default) pci 0000:00:02.0: Boot video device pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup =
0x0f30
pci 0000:00:1d.0: Performing full reset pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup =
0x0030
pci 0000:00:1d.1: Performing full reset pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup =
0x0030
pci 0000:00:1d.2: Performing full reset pci 0000:00:1d.3: uhci_check_and_reset_hc: legsup =
0x0030
pci 0000:00:1d.3: Performing full reset pcieport-driver 0000:00:1c.0: setting latency timer to
64
pcieport-driver 0000:00:1c.0: found MSI capability pci_express 0000:00:1c.0:pcie00: allocate port service pci_express 0000:00:1c.0:pcie02: allocate port service pci_express 0000:00:1c.0:pcie03: allocate port service pcieport-driver 0000:00:1c.1: setting latency timer to
64
pcieport-driver 0000:00:1c.1: found MSI capability pci_express 0000:00:1c.1:pcie00: allocate port service pci_express 0000:00:1c.1:pcie02: allocate port service pci_express 0000:00:1c.1:pcie03: allocate port service pcieport-driver 0000:00:1c.2: setting latency timer to
64
pcieport-driver 0000:00:1c.2: found MSI capability pci_express 0000:00:1c.2:pcie00: allocate port service pci_express 0000:00:1c.2:pcie02:allocate port service pci_express 0000:00:1c.2:pcie03:allocate port service pci_hotplug: PCI Hot Plug PCI Core version: 0.5 input: Power Button (FF) as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button (FF) [PWRF] input: Lid Switch as
/devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
ACPI: EC: non-query interrupt received, switching to
interrupt mode
ACPI: Lid Switch [LID] input: Sleep Buttion (CM) as /devices/LNXSYSTM:00/device:00/PP0C0E:00/input/input2 ACPI: Sleep Button (CM) [SLPB] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3 ACPI: Power Button (CM) [PWRB] ACPI: CPU0 (power statesL C1[C1] C2[C2] C3[C3]) processor ACPI0007:00: registered as cooling_device0 ACPI: Processor [CPU1] (supports 8 throttling states) thermal LNXTHERM:01: registered as thermal_zone0 ACPI: Thermal Zone [TZ00] (35 C) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Non-volatile memory driver v1.2 Linux agpgart interface v0.103 agpgart-intel 0000:00:00.0: Intel 915GM Chipset agpgart-intel 0000:00:00.0: detected 7932K stolen
memory
agpgart-intel 0000:00:00.0: AGP aperture is 256M @
0xd0000000
Serial: 8250/16550 driver4 ports, IRQ sharing enabled brd: module loaded input: Macintosh mouse button emulation as
/devices/virtual/input/input4
Driver 'sd' needs updating - please use
bus_type methods
ehci_hcd: block sizes: qh 128 qtd 96 itd 160 sitd 96 ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level,
low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller drivers/usb/core/inode.c: creating file
'devices'
drivers/usb/core/inode.c: creating file '001' ehci_hcd 0000:00:1d.7: new USB bus registered,
assigned bus number 1
ehci_hcd 0000:00:1d.7: reset hcs_params 0x104208 dbg=1
cc=4 pcc=2 ordered
!ppc ports=8 ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7
uframes 1024 64 bit
addr ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0
ithresh=8 period=1024
Reset HALT ehci_hcd 0000:00:1d.7: debug port 1 ehci_hcd 0000:00:1d.7: cache line size of 32 is not
supported
ehci_hcd 0000:00:1d.7: supports USB remote wakeup ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf7eb7c00 ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0
ithresh=8 period=1024
Reset HALT ehci_hcd 0000:00:1d.7: init command 010001 (park)=0
ithresh=1 period-1024
RUN ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00,
driver 10 Dec 2004
usb usb1: default language 0x409 usb usb1: uevent usb usb1: usb_probe_device usb usb1: configuration #1 chosen from 1 choice usb usb1: adding 1-0:1.0 (config #1, interface 0) usb 1-0:1.0: uevent hub 1-0:1.0: usb_probe_interface hub 1-0:1.0: usb_probe_interface - got id hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected hub 1-0:1.0: standalone hub hub 1-0:1.0: no power switching (usb 1.0) hub 1-0:1.0: individual port over-current protection hub 1-0:1.0: power on to power good time: 20ms hub 1-0:1.0: local power source is good hub 1-0:1.0: trying to enable port power on
non-switchable hub
ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001803
POWER sig=j CSC
CONNECT hub 1-0:1.0: port 5: status 0501 change 0001 hub 1-0:1.0: state 7 ports 8 chg 0020 evt 0000 drivers/usb/core/inode.c: creating file '001' hub 1-0:1.0: port 5, status 0501, change 0000, 480
Mb/s
usb usb1: New USB device found, idVendor=1d6b,
idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux
2.6.27-0.287.rc4.git7.fc10.i686 ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7 ohci_hcd: 2006 August 04 USB 1.1 'Open' Host
Controller (OHCI) Driver
ohci_hcd: block sizes: ed 64 td 64 USB Universal Host Controller Interface driver v3.0 uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level,
low) -> IRQ 23
uhci_hcd 0000:00:1d.0: setting latency timer to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller drivers/usb/core/inode.c: creating file '002' uhci_hcd 0000:00:1d.0: new USB bus registered,
assigned bus number 2
uhci_hcd 0000:00:1d.0: detected 2 ports uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd =
0x0000
uhci_hcd 0000:00:1d.0: Performing full reset uhci_hcd 0000:00:1d.0: supports USB remote wakeup uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e400 usb usb3: default language 0x409 usb usb3: uevent usb usb3: usb_probe_device usb usb3: configuration #1 chosen from 1 choice usb usb3: adding 2-0:1.0 (config #1, interface 0) usb 2-0:1.0: uevent hub 2-0:1.0: usb_probe_interface hub 2-0:1.0: usb_probe_interface - got id hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected hub 2-0:1.0: standalone hub hub 2-0:1.0: no power switching (usb 1.0) hub 2-0:1.0: individual port over-current protection hub 2-0:1.0: power on to power good time: 2ms hub 2-0:1.0: local power source is good hub 2-0:1.0: trying to enable port power on
non-switchable hub
ehci_hcd 0000:00:1d.7: port 5 high speed ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005
POWER sig=se0 PE
CONNECT usb 1-5: new high speed USB device using ehci_hcd and
address 2
drivers/usb/core/inode.c: creating file '001' usb usb2: New USB device found, idVendor=1d6b,
idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
usb usb2: Product: UHCI Host Controller usb usb2: Manufacturer: Linux
2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0 uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level,
low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller drivers/usb/core/inode.c: creating file '003' uhci_hcd 0000:00:1d.1: new USB bus registered,
assigned bus number 3
uhci_hcd 0000:00:1d.1: detected 2 ports uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd =
0x0000
uhci_hcd 0000:00:1d.1: Performing full reset uhci_hcd 0000:00:1d.1: supports USB remote wakeup uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e480 usb usb3: default language 0x409 usb usb3: uevent usb usb3: usb_probe_device usb usb3: configuration #1 chosen from 1 choice usb usb3: adding 3-0:1.0 (config #1, interface 0) usb 3-0:1.0: uevent hub 3-0:1.0: usb_probe_interface hub 3-0:1.0: usb_probe_interface - got id hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected hub 3-0:1.0: standalone hub hub 3-0:1.0: no power switching (usb 1.0) hub 3-0:1.0: individual port over-current protection hub 3-0:1.0: power on to power good time: 2ms hub 3-0:1.0: local power source is good hub 3-0:1.0: trying to enable port power on
non-switchable hub
ehci_hcd 0000:00:1d.7: port 5 high speed ehci_hcd 0000:00:1d.7: GetStatus port 5 status 001005
POWER sig=se0 PE
CONNECT usb 1-5: default language 0x0409 usb 1-5: uevent usb 1-5: usb_probe_device usb 1-5: configuration #1 chosen from 1 choice usb 1-5: adding 1-5:1.0 (config #1, interface 0) usb 1-5:1.0: uevent drivers/usb/core/inode.c: creating file '002' usb 1-5: New USB device found, idVendor=0951,
idProduct=1606
usb 1-5: New USB device strings: Mfr=1, Product=2,
SerialNumber=4
usb 1-5: Product: UB6225 usb 1-5: Manufacturer: ENE usb 1-5: SerialNumber: 146030377350 hub 2-0:1.0: state 7 ports 2 chg 0000 evt 0000 hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 drivers/usb/core/inode.c: creating file '001' usb usb3: New USB device found, idVendor=1d6b,
idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
usb usb3: Product: UHCI Host Controller usb usb3: Manufacturer: Linux
2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1 uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level,
low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller drivers/usb/core/inode.c: creating file '004' uhci_hcd 0000:00:1d.2: new USB bus registered,
assigned bus number 4
uhci_hcd 0000:00:1d.2: detected 2 ports uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd =
0x0000
uhci_hcd 0000:00:1d.2: Performing full reset uhci_hcd 0000:00:1d.2: supports USB remote wakeup uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e800 usb usb4: default language 0x409 usb usb4: uevent usb usb4: usb_probe_device usb usb4: configuration #1 chosen from 1 choice usb usb4: adding 4-0:1.0 (config #1, interface 0) usb 4-0:1.0: uevent usb 4-0:1.0: usb_probe_interface usb 4-0:1.0: usb_probe_interface - got id usb 4-0:1.0: USB hub found usb 4-0:1.0: 2 ports detected usb 4-0:1.0: standalone hub usb 4-0:1.0: no power switching (usb 1.0) usb 4-0:1.0: individual port over-current protection usb 4-0:1.0: power on to power good time: 2ms usb 4-0:1.0: local power source is good usb 4-0:1.0: trying to enable port power on
non-switchable hub
uhci_hcd 0000:00:1d.2: port 1 portsc 0082,00 usb 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 drivers/usb/core/inode.c: creating file '001' usb usb4: New USB device found, idVendor=1d6b,
idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
usb usb4: Product: UHCI Host Controller usb usb4: Manufacturer: Linux
2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2 uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level,
low) -> IRQ 16
uhci_hcd 0000:00:1d.3: setting latency timer to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller drivers/usb/core/inode.c: creating file '005' uhci_hcd 0000:00:1d.3: new USB bus registered,
assigned bus number 5
uhci_hcd 0000:00:1d.3: detected 2 ports uhci_hcd 0000:00:1d.3: uhci_check_and_reset_hc: cmd =
0x0000
uhci_hcd 0000:00:1d.3: Performing full reset uhci_hcd 0000:00:1d.3: supports USB remote wakeup uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e880 usb usb5: default language 0x409 usb usb5: uevent usb usb5: usb_probe_device usb usb5: configuration #1 chosen from 1 choice usb usb5: adding 5-0:1.0 (config #1, interface 0) usb 5-0:1.0: uevent usb 5-0:1.0: usb_probe_interface usb 5-0:1.0: usb_probe_interface - got id usb 5-0:1.0: USB hub found usb 5-0:1.0: 2 ports detected hub 5-0:1.0: standalone hub hub 5-0:1.0: no power switching (usb 1.0) hub 5-0:1.0: individual port over-current protection hub 5-0:1.0: power on to power good time: 2ms hub 5-0:1.0: local power source is good hub 5-0:1.0: trying to enable port power on
non-switchable hub
hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000 drivers/usb/core/inode.c: creating file '001' usb usb5: New USB device found, idVendor=1d6b,
idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
usb usb5: Product: UHCI Host Controller usb usb5: Manufacturer: Linux
2.6.27-0.287.rc4.git7.fc10.i686 uhci_hcd
usb usb5: SerialNumber: 0000:00:1d.3 PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at
0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1 Setting up hotplug.rt at 0x60,0x64 irq 12 Creating block device nodes.on for all mice Loading ext3 module core: registered rtc_cmos as rtc0 usb usb2: suspend_rh (auto-stop)et irqs usb usb3: suspend_rh (auto-stop) Loading usb-storage modulenu Initializing USB Mass Storage driver...r hiddev usb-storage 1-5:1.0: usb_probe_interface usbhid usb-storage 1-5:1.0: usb_probe_interface - got id scsi0 : SCSI emulation for USB Mass Storage devices usbcore: registered new interface driver usb-storage USB Mass Storage support registered. Waiting for driver initialization. stabilized: stat /proc/bus/usb/devices: No such file
or directory
Creating root device. :941 usb-storage: device found at 207f9000..c096d000 usb-storage: waiting for device to settle before
scaning
Mounting root filesystem.2 keyboard as /devices/platform/i8042/serio/input/inpu mount: error mounting /dev/root on /sysroot as ext3:
No such file or
directory Setting up other filesystems. setuproot: moving /dev failed: No such file or
directory
setuproot: error mounting /proc: No such file or
directory
setuproot: error mounting /sys: No such file or
directory
Mount failed for selinuxfs on /selinux: No such file
or directory
Switching to new root and running init. switchroot: mount failed: No such file or directory Booting has failed. usb usb4: suspend_rh (auto-stop) Synaptics Touchpad, model: 1, fw: 6.5, id: 0x1c0b1,
caps: 0xa04751/0xa00000
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6 usb usb5: suspend_rh (auto-stop) hub 2-0:1.0: hub_suspend usb usb2: bus auto-suspend usb usb2: suspend_rh hub 3-0:1.0: hub_suspend usb usb3: bus auto-suspend usb usb3: suspend_rh hub 4-0:1.0: hub_suspend usb usb4: bus auto-suspend usb usb4: suspend_rh hub 5-0:1.0: hub_suspend usb usb5: bus auto-suspend usb usb5: suspend_rh usb-storage: device scan complete scsi 0:0:0:0: Direct-Access USB2.0 CardReader
SD0 0100 PQ: 0 ANSI: 0
sd 0:0:0:0: [sda] 15954944 512-byte hardware sectors
(8169 MB)
sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00 sd 0:0:0:0: Assuming drive cache: write through sd 0:0:0:0: 15954944 512-byte hardware sectors (8169
MB)
sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00 sd 0:0:0:0: Assuming drive cache: write through sda: sda1 sda2 sd 0:0:0:0: [sda] Attached SCSI removable disk sd 0:0:0:0: Attached SCSI generic sg0 type 0 scsi_scan_0 used greatest stack depth: 1928 bytes left
-- fedora-test-list mailing list fedora-test-list@redhat.com To unsubscribe:
https://www.redhat.com/mailman/listinfo/fedora-test-list
also 287 has exactly same problem.....that means that nobody read this thread :-( and I spent some time to install and de-install the kernel.
It happens at some point or another. I installed the 284 kernel and it
worked for me. However I even installed the 290 kernel and it worked! Things like this happen to us at one point or another. I have also needed to remove several kernels that were not working for me :)
BTW, thank you for bringing up the printing problem. I am having
problems printing as well. We are here and we do read the thread(s). Sorry I could not have provided advice since those kernels booted for me :(
-- Antonio Montagnani Skype : antoniomontag
--
Regards,
Antonio
-- fedora-test-list mailing list fedora-test-list@redhat.com To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-test-list
even kernel-2.6.27-0.290.rc5.fc10.i686 is not booting off my USB HD drive, with same problems of other two kernels. Latest kernel booting off an USB HD drive is kernel-2.6.27-0.244.rc2.git1.fc10.i686.
-- Antonio Montagnani Skype : antoniomontag
filed a bug: Bug 460762 - Recent kernels don't boot off USB deviceshttps://bugzilla.redhat.com/show_bug.cgi?id=460762 Please add your comments
-- Antonio Montagnani Skype : antoniomontag
-
Andrew Gormanly -
Antonio M -
Antonio Olivares