Hi, all,
I installed a fresh copy of FC3 into my Dad's machine and everything worked fine. However, when I brought the machine to my Dad's place and plugged in his monitor (Acer 7154e), X crashes no matter what. I tried config xorg.conf with the correct HorizSync and VertRefresh, but it didn't even make any difference.
Then I tried the extreme solution: I replaced the HDD with a new HDD and installed a fresh copy FC3 with my Dad's monitor plugged in while installation. Everything worked fine again and I got graphics interface. I then grabbed the working xorg.conf and swapped the HDDs. After I booted into the previous installed FC3, I replaced the xorg.conf with the working xorg.conf. It still didn't make any difference!
I am a little confused. Is there some other file I need to change except for /etc/X11/xorg.conf? Is there any special module I need to load?
I know I could just re-install FC3 into my Dad's HDD. I am just curious to see what's wrong here.
Here's the setup: AMD K6 350Mhz; 196MB RAM Trident Blade3D 8MB video card
Thanks in advance!
Ben.
Here comes the log file: /var/log/Xorg.0.log: ---------------------------------------------------------------------------------
X Window System Version 6.8.1 Release Date: 17 September 2004 X Protocol Version 11, Revision 0, Release 6.8.1 Build Operating System: Linux 2.4.21-14.ELsmp i686 [ELF] Current Operating System: Linux fallsview 2.6.9-1.667 #1 Tue Nov 2 14:41:31 EST 2004 i586 Build Date: 20 October 2004 Build Host: tweety.build.redhat.com
Before reporting problems, check http://wiki.X.Org to make sure that you have the latest version. Module Loader present OS Kernel: Linux version 2.6.9-1.667 (bhcompile@tweety.build.redhat.com) (gcc version 3.4.2 20041017 (Red Hat 3.4.2-6.fc3)) #1 Tue Nov 2 14:41:31 EST 2004 Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Sat Jan 1 02:56:07 2000 (++) Using config file: "xorg.conf.new" (==) ServerLayout "Default Layout" (**) |-->Screen "Screen0" (0) (**) | |-->Monitor "Monitor0" (**) | |-->Device "Videocard0" (**) |-->Input Device "Mouse0" (**) |-->Input Device "Keyboard0" (**) FontPath set to "unix/:7100" (**) RgbPath set to "/usr/X11R6/lib/X11/rgb" (==) ModulePath set to "/usr/X11R6/lib/modules" (WW) Open APM failed (/dev/apm_bios) (No such file or directory) (II) Module ABI versions: X.Org ANSI C Emulation: 0.2 X.Org Video Driver: 0.7 X.Org XInput driver : 0.4 X.Org Server Extension : 0.2 X.Org Font Renderer : 0.4 (II) Loader running on linux (II) LoadModule: "bitmap" (II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.a (II) Module bitmap: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 Module class: X.Org Font Renderer ABI class: X.Org Font Renderer, version 0.4 (II) Loading font Bitmap (II) LoadModule: "pcidata" (II) Loading /usr/X11R6/lib/modules/libpcidata.a (II) Module pcidata: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org Video Driver, version 0.7 (--) using VT number 7
(II) PCI: Probing config type using method 1 (II) PCI: Config type is 1 (II) PCI: stages = 0x03, oldVal1 = 0x00000000, mode1Res1 = 0x80000000 (II) PCI: PCI scan (all values are in hex) (II) PCI: 00:00:0: chip 1106,0598 card 0000,0000 rev 04 class 06,00,00 hdr 00 (II) PCI: 00:01:0: chip 1106,8598 card 0000,0000 rev 00 class 06,04,00 hdr 01 (II) PCI: 00:07:0: chip 1106,0686 card 1106,0000 rev 22 class 06,01,00 hdr 80 (II) PCI: 00:07:1: chip 1106,0571 card 0000,0000 rev 10 class 01,01,8a hdr 00 (II) PCI: 00:07:2: chip 1106,3038 card 0925,1234 rev 10 class 0c,03,00 hdr 00 (II) PCI: 00:07:3: chip 1106,3038 card 0925,1234 rev 10 class 0c,03,00 hdr 00 (II) PCI: 00:07:4: chip 1106,3057 card 0000,0000 rev 30 class 06,00,00 hdr 00 (II) PCI: 00:08:0: chip 122d,50dc card 122d,8000 rev 10 class 04,01,00 hdr 00 (II) PCI: 00:0b:0: chip 10d9,0531 card 15e8,8110 rev 25 class 02,00,00 hdr 00 (II) PCI: 01:00:0: chip 1023,9880 card 1023,9880 rev 3a class 03,00,00 hdr 00 (II) PCI: End of PCI scan (II) Host-to-PCI bridge: (II) Bus 0: bridge is at (0:0:0), (0,0,1), BCTRL: 0x0008 (VGA_EN is set) (II) Bus 0 I/O range: [0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B] (II) Bus 0 non-prefetchable memory range: [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B] (II) Bus 0 prefetchable memory range: [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B] (II) PCI-to-PCI bridge: (II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x000c (VGA_EN is set) (II) Bus 1 non-prefetchable memory range: [0] -1 0 0xd4000000 - 0xd7ffffff (0x4000000) MX[B] (II) PCI-to-ISA bridge: (II) Bus -1: bridge is at (0:7:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set) (II) Host-to-PCI bridge: (II) Bus -1: bridge is at (0:7:4), (-1,-1,1), BCTRL: 0x0008 (VGA_EN is set) (II) Bus -1 I/O range: [0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B] (II) Bus -1 non-prefetchable memory range: [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B] (II) Bus -1 prefetchable memory range: [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B] (--) PCI:*(1:0:0) Trident Microsystems Blade 3D PCI/AGP rev 58, Mem @ 0xd5800000/23, 0xd6000000/17, 0xd5000000/23 (II) Addressable bus resource ranges are [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B] [1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B] (II) OS-reported resource ranges: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] (II) PCI Memory resource overlap reduced 0xd0000000 from 0xd3ffffff to 0xcfffffff (II) Active PCI resource ranges: [0] -1 0 0xd9000000 - 0xd90000ff (0x100) MX[B] [1] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O [2] -1 0 0xd5000000 - 0xd57fffff (0x800000) MX[B](B) [3] -1 0 0xd6000000 - 0xd601ffff (0x20000) MX[B](B) [4] -1 0 0xd5800000 - 0xd5ffffff (0x800000) MX[B](B) [5] -1 0 0x0000e000 - 0x0000e0ff (0x100) IX[B] [6] -1 0 0x0000dc00 - 0x0000dc3f (0x40) IX[B] [7] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B] [8] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B] [9] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B] [10] -1 0 0x0000cc00 - 0x0000cc7f (0x80) IX[B] [11] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B] [12] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B] [13] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B] (II) Active PCI resource ranges after removing overlaps: [0] -1 0 0xd9000000 - 0xd90000ff (0x100) MX[B] [1] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O [2] -1 0 0xd5000000 - 0xd57fffff (0x800000) MX[B](B) [3] -1 0 0xd6000000 - 0xd601ffff (0x20000) MX[B](B) [4] -1 0 0xd5800000 - 0xd5ffffff (0x800000) MX[B](B) [5] -1 0 0x0000e000 - 0x0000e0ff (0x100) IX[B] [6] -1 0 0x0000dc00 - 0x0000dc3f (0x40) IX[B] [7] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B] [8] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B] [9] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B] [10] -1 0 0x0000cc00 - 0x0000cc7f (0x80) IX[B] [11] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B] [12] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B] [13] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B] (II) OS-reported resource ranges after removing overlaps with PCI: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] (II) All system resource ranges: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0xd9000000 - 0xd90000ff (0x100) MX[B] [6] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O [7] -1 0 0xd5000000 - 0xd57fffff (0x800000) MX[B](B) [8] -1 0 0xd6000000 - 0xd601ffff (0x20000) MX[B](B) [9] -1 0 0xd5800000 - 0xd5ffffff (0x800000) MX[B](B) [10] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [11] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [12] -1 0 0x0000e000 - 0x0000e0ff (0x100) IX[B] [13] -1 0 0x0000dc00 - 0x0000dc3f (0x40) IX[B] [14] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B] [15] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B] [16] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B] [17] -1 0 0x0000cc00 - 0x0000cc7f (0x80) IX[B] [18] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B] [19] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B] [20] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B] (II) LoadModule: "dbe" (II) Loading /usr/X11R6/lib/modules/extensions/libdbe.a (II) Module dbe: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 0.2 (II) Loading extension DOUBLE-BUFFER (II) LoadModule: "extmod" (II) Loading /usr/X11R6/lib/modules/extensions/libextmod.a (II) Module extmod: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 0.2 (II) Loading extension SHAPE (II) Loading extension MIT-SUNDRY-NONSTANDARD (II) Loading extension BIG-REQUESTS (II) Loading extension SYNC (II) Loading extension MIT-SCREEN-SAVER (II) Loading extension XC-MISC (II) Loading extension XFree86-VidModeExtension (II) Loading extension XFree86-Misc (II) Loading extension XFree86-DGA (II) Loading extension DPMS (II) Loading extension TOG-CUP (II) Loading extension Extended-Visual-Information (II) Loading extension XVideo (II) Loading extension XVideo-MotionCompensation (II) Loading extension X-Resource (II) LoadModule: "fbdevhw" (II) Loading /usr/X11R6/lib/modules/linux/libfbdevhw.a (II) Module fbdevhw: vendor="X.Org Foundation" compiled for 6.8.1, module version = 0.0.2 ABI class: X.Org Video Driver, version 0.7 (II) LoadModule: "glx" (II) Loading /usr/X11R6/lib/modules/extensions/libglx.a (II) Module glx: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org Server Extension, version 0.2 (II) Loading sub module "GLcore" (II) LoadModule: "GLcore" (II) Loading /usr/X11R6/lib/modules/extensions/libGLcore.a (II) Module GLcore: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org Server Extension, version 0.2 (II) Loading extension GLX (II) LoadModule: "record" (II) Loading /usr/X11R6/lib/modules/extensions/librecord.a (II) Module record: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.13.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 0.2 (II) Loading extension RECORD (II) LoadModule: "freetype" (II) Loading /usr/X11R6/lib/modules/fonts/libfreetype.so (II) Module freetype: vendor="X.Org Foundation & the After X-TT Project" compiled for 6.8.1, module version = 2.1.0 Module class: X.Org Font Renderer ABI class: X.Org Font Renderer, version 0.4 (II) Loading font FreeType (II) LoadModule: "type1" (II) Loading /usr/X11R6/lib/modules/fonts/libtype1.a (II) Module type1: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.2 Module class: X.Org Font Renderer ABI class: X.Org Font Renderer, version 0.4 (II) Loading font Type1 (II) Loading font CID (II) LoadModule: "dri" (II) Loading /usr/X11R6/lib/modules/extensions/libdri.a (II) Module dri: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org Server Extension, version 0.2 (II) Loading sub module "drm" (II) LoadModule: "drm" (II) Loading /usr/X11R6/lib/modules/linux/libdrm.a (II) Module drm: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org Server Extension, version 0.2 (II) Loading extension XFree86-DRI (II) LoadModule: "trident" (II) Loading /usr/X11R6/lib/modules/drivers/trident_drv.o (II) Module trident: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 Module class: X.Org Video Driver ABI class: X.Org Video Driver, version 0.7 (II) LoadModule: "mouse" (II) Loading /usr/X11R6/lib/modules/input/mouse_drv.o (II) Module mouse: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 Module class: X.Org XInput Driver ABI class: X.Org XInput driver, version 0.4 (II) LoadModule: "kbd" (II) Loading /usr/X11R6/lib/modules/input/kbd_drv.o (II) Module kbd: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 Module class: X.Org XInput Driver ABI class: X.Org XInput driver, version 0.4 (II) TRIDENT: driver for Trident chipsets: tvga9000, tvga9000i, tvga8900c, tvga8900d, tvga9200cxr, tgui9400cxi, cyber9320, cyber9388, cyber9397, cyber9397dvd, cyber9520, cyber9525dvd, cyberblade/e4, tgui9420dgi, tgui9440agi, tgui9660, tgui9680, providia9682, providia9685, cyber9382, cyber9385, 3dimage975, 3dimage985, blade3d, cyberbladei7, cyberbladei7d, cyberbladei1, cyberbladei1d, cyberbladeAi1, cyberbladeAi1d, bladeXP, cyberbladeXPAi1, cyberbladeXP4 (II) Primary Device is: PCI 01:00:0 (--) Assigning device section with no busID to primary device (--) Chipset blade3d found (II) resource ranges after xf86ClaimFixedResources() call: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0xd9000000 - 0xd90000ff (0x100) MX[B] [6] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O [7] -1 0 0xd5000000 - 0xd57fffff (0x800000) MX[B](B) [8] -1 0 0xd6000000 - 0xd601ffff (0x20000) MX[B](B) [9] -1 0 0xd5800000 - 0xd5ffffff (0x800000) MX[B](B) [10] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [11] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [12] -1 0 0x0000e000 - 0x0000e0ff (0x100) IX[B] [13] -1 0 0x0000dc00 - 0x0000dc3f (0x40) IX[B] [14] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B] [15] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B] [16] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B] [17] -1 0 0x0000cc00 - 0x0000cc7f (0x80) IX[B] [18] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B] [19] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B] [20] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B] (II) resource ranges after probing: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0xd9000000 - 0xd90000ff (0x100) MX[B] [6] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O [7] -1 0 0xd5000000 - 0xd57fffff (0x800000) MX[B](B) [8] -1 0 0xd6000000 - 0xd601ffff (0x20000) MX[B](B) [9] -1 0 0xd5800000 - 0xd5ffffff (0x800000) MX[B](B) [10] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B] [11] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B] [12] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B] [13] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [14] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [15] -1 0 0x0000e000 - 0x0000e0ff (0x100) IX[B] [16] -1 0 0x0000dc00 - 0x0000dc3f (0x40) IX[B] [17] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B] [18] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B] [19] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B] [20] -1 0 0x0000cc00 - 0x0000cc7f (0x80) IX[B] [21] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B] [22] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B] [23] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B] [24] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B] [25] 0 0 0x000003c0 - 0x000003df (0x20) IS[B] (II) Setting vga for screen 0. (**) TRIDENT(0): Depth 16, (--) framebuffer bpp 16 (II) Loading sub module "vgahw" (II) LoadModule: "vgahw" (II) Loading /usr/X11R6/lib/modules/libvgahw.a (II) Module vgahw: vendor="X.Org Foundation" compiled for 6.8.1, module version = 0.1.0 ABI class: X.Org Video Driver, version 0.7 (II) TRIDENT(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000 (II) Loading sub module "ramdac" (II) LoadModule: "ramdac" (II) Loading /usr/X11R6/lib/modules/libramdac.a (II) Module ramdac: vendor="X.Org Foundation" compiled for 6.8.1, module version = 0.1.0 ABI class: X.Org Video Driver, version 0.7 (==) TRIDENT(0): RGB weight 565 (==) TRIDENT(0): Default visual is TrueColor (==) TRIDENT(0): Using gamma correction (1.0, 1.0, 1.0) (==) TRIDENT(0): Linear framebuffer at 0xD5800000 (--) TRIDENT(0): IO registers at 0xD6000000 (II) Loading sub module "vbe" (II) LoadModule: "vbe" (II) Loading /usr/X11R6/lib/modules/libvbe.a (II) Module vbe: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.1.0 ABI class: X.Org Video Driver, version 0.7 (II) Loading sub module "int10" (II) LoadModule: "int10" (II) Loading /usr/X11R6/lib/modules/linux/libint10.a (II) Module int10: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org Video Driver, version 0.7 (II) TRIDENT(0): initializing int10 (II) TRIDENT(0): Primary V_BIOS segment is: 0xc000 (II) TRIDENT(0): VESA BIOS detected (II) TRIDENT(0): VESA VBE Version 2.0 (II) TRIDENT(0): VESA VBE Total Mem: 8192 kB (II) TRIDENT(0): VESA VBE OEM: Trident Blade 3D (II) TRIDENT(0): VESA VBE OEM Software Rev: 2.0 (II) TRIDENT(0): VESA VBE OEM Vendor: TRIDENT MICROSYSTEMS INC. (II) TRIDENT(0): VESA VBE OEM Product: Blade 3D (II) TRIDENT(0): VESA VBE OEM Product Rev: J 6.4 (38) (II) Loading sub module "ddc" (II) LoadModule: "ddc" (II) Loading /usr/X11R6/lib/modules/libddc.a (II) Module ddc: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org Video Driver, version 0.7 (II) TRIDENT(0): VESA VBE DDC supported (II) TRIDENT(0): VESA VBE DDC Level 2 (II) TRIDENT(0): VESA VBE DDC transfer in appr. 1 sec. (II) TRIDENT(0): VESA VBE DDC read successfully (II) Loading sub module "ddc" (II) LoadModule: "ddc" (II) Reloading /usr/X11R6/lib/modules/libddc.a (II) TRIDENT(0): Manufacturer: API Model: 4536 Serial#: 924 (II) TRIDENT(0): Year: 1997 Week: 26 (II) TRIDENT(0): EDID Version: 1.2 (II) TRIDENT(0): Analog Display Input, Input Voltage Level: 0.700/0.300 V (II) TRIDENT(0): Sync: Separate (II) TRIDENT(0): Max H-Image Size [cm]: horiz.: 27 vert.: 20 (II) TRIDENT(0): Gamma: 2.66 (II) TRIDENT(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display (II) TRIDENT(0): redX: 0.625 redY: 0.340 greenX: 0.284 greenY: 0.600 (II) TRIDENT(0): blueX: 0.149 blueY: 0.064 whiteX: 0.280 whiteY: 0.311 (II) TRIDENT(0): Supported VESA Video Modes: (II) TRIDENT(0): 720x400@70Hz (II) TRIDENT(0): 640x480@60Hz (II) TRIDENT(0): 640x480@72Hz (II) TRIDENT(0): 640x480@75Hz (II) TRIDENT(0): 800x600@60Hz (II) TRIDENT(0): 800x600@72Hz (II) TRIDENT(0): 800x600@75Hz (II) TRIDENT(0): 1024x768@60Hz (II) TRIDENT(0): Manufacturer's mask: 21 (--) TRIDENT(0): Revision is 58 (--) TRIDENT(0): Found Blade3D chip (--) TRIDENT(0): RAM type is SDRAM (--) TRIDENT(0): Using HW cursor (--) TRIDENT(0): VideoRAM: 8192 kByte (--) TRIDENT(0): Memory Clock is 109.77 MHz (==) TRIDENT(0): Min pixel clock is 12 MHz (--) TRIDENT(0): Max pixel clock is 230 MHz (II) TRIDENT(0): Monitor0: Using hsync range of 31.00-60.00 kHz (II) TRIDENT(0): Monitor0: Using vrefresh range of 55.00-90.00 Hz (II) TRIDENT(0): Clock range: 12.00 to 230.00 MHz (II) TRIDENT(0): Not using default mode "320x175" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "320x200" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "360x200" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1024x768" (hsync out of range) (II) TRIDENT(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1152x864" (hsync out of range) (II) TRIDENT(0): Not using default mode "576x432" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1280x960" (hsync out of range) (II) TRIDENT(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1280x1024" (hsync out of range) (II) TRIDENT(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1280x1024" (hsync out of range) (II) TRIDENT(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1280x1024" (hsync out of range) (II) TRIDENT(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1600x1200" (hsync out of range) (II) TRIDENT(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1600x1200" (hsync out of range) (II) TRIDENT(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1600x1200" (hsync out of range) (II) TRIDENT(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1600x1200" (hsync out of range) (II) TRIDENT(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1600x1200" (hsync out of range) (II) TRIDENT(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1792x1344" (hsync out of range) (II) TRIDENT(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1792x1344" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1856x1392" (hsync out of range) (II) TRIDENT(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1856x1392" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "416x312" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "576x384" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1152x864" (hsync out of range) (II) TRIDENT(0): Not using default mode "576x432" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1400x1050" (hsync out of range) (II) TRIDENT(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1400x1050" (hsync out of range) (II) TRIDENT(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1400x1050" (hsync out of range) (II) TRIDENT(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1400x1050" (hsync out of range) (II) TRIDENT(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1600x1024" (hsync out of range) (II) TRIDENT(0): Not using default mode "800x512" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1920x1200" (hsync out of range) (II) TRIDENT(0): Not using default mode "960x600" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1280x960" (width too large for virtual size) (II) TRIDENT(0): Not using default mode "1152x768" (width too large for virtual size) (II) TRIDENT(0): Not using default mode "1024x768" (width too large for virtual size) (II) TRIDENT(0): Not using default mode "1024x768" (width too large for virtual size) (II) TRIDENT(0): Not using default mode "1024x768" (width too large for virtual size) (II) TRIDENT(0): Not using default mode "1024x768" (width too large for virtual size) (II) TRIDENT(0): Not using default mode "832x624" (width too large for virtual size) (--) TRIDENT(0): Virtual size is 800x600 (pitch 800) (**) TRIDENT(0): *Default mode "800x600": 56.3 MHz, 53.7 kHz, 85.1 Hz (II) TRIDENT(0): Modeline "800x600" 56.30 800 832 896 1048 600 601 604 631 +hsync +vsync (**) TRIDENT(0): *Default mode "640x480": 36.0 MHz, 43.3 kHz, 85.0 Hz (II) TRIDENT(0): Modeline "640x480" 36.00 640 696 752 832 480 481 484 509 -hsync -vsync (**) TRIDENT(0): Default mode "800x600": 49.5 MHz, 46.9 kHz, 75.0 Hz (II) TRIDENT(0): Modeline "800x600" 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (**) TRIDENT(0): Default mode "800x600": 50.0 MHz, 48.1 kHz, 72.2 Hz (II) TRIDENT(0): Modeline "800x600" 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (**) TRIDENT(0): Default mode "800x600": 40.0 MHz, 37.9 kHz, 60.3 Hz (II) TRIDENT(0): Modeline "800x600" 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (**) TRIDENT(0): Default mode "800x600": 36.0 MHz, 35.2 kHz, 56.2 Hz (II) TRIDENT(0): Modeline "800x600" 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (**) TRIDENT(0): Default mode "640x480": 31.5 MHz, 37.5 kHz, 75.0 Hz (II) TRIDENT(0): Modeline "640x480" 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (**) TRIDENT(0): Default mode "640x480": 31.5 MHz, 37.9 kHz, 72.8 Hz (II) TRIDENT(0): Modeline "640x480" 31.50 640 664 704 832 480 489 491 520 -hsync -vsync (**) TRIDENT(0): Default mode "640x480": 25.2 MHz, 31.5 kHz, 60.0 Hz (II) TRIDENT(0): Modeline "640x480" 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (**) TRIDENT(0): Default mode "720x400": 35.5 MHz, 37.9 kHz, 85.0 Hz (II) TRIDENT(0): Modeline "720x400" 35.50 720 756 828 936 400 401 404 446 -hsync +vsync (**) TRIDENT(0): Default mode "640x400": 31.5 MHz, 37.9 kHz, 85.1 Hz (II) TRIDENT(0): Modeline "640x400" 31.50 640 672 736 832 400 401 404 445 -hsync +vsync (**) TRIDENT(0): Default mode "640x350": 31.5 MHz, 37.9 kHz, 85.1 Hz (II) TRIDENT(0): Modeline "640x350" 31.50 640 672 736 832 350 382 385 445 +hsync -vsync (**) TRIDENT(0): Display dimensions: (270, 200) mm (**) TRIDENT(0): DPI set to (75, 76) (II) Loading sub module "fb" (II) LoadModule: "fb" (II) Loading /usr/X11R6/lib/modules/libfb.a (II) Module fb: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org ANSI C Emulation, version 0.2 (II) Loading sub module "i2c" (II) LoadModule: "i2c" (II) Loading /usr/X11R6/lib/modules/libi2c.a (II) Module i2c: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.2.0 ABI class: X.Org Video Driver, version 0.7 (II) Loading sub module "xaa" (II) LoadModule: "xaa" (II) Loading /usr/X11R6/lib/modules/libxaa.a (II) Module xaa: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.2.0 ABI class: X.Org Video Driver, version 0.7
*** If unresolved symbols were reported above, they might not *** be the reason for the server aborting.
Fatal server error: Caught signal 11. Server aborting
Please consult the The X.Org Foundation support at http://wiki.X.Org for help. Please also check the log file at "/var/log/Xorg.0.log" for additional information.
On Mon, 07 Mar 2005 09:38:11 -0500, Benjamin Jiang bjiang_ee@yahoo.ca wrote:
Hi, all,
I installed a fresh copy of FC3 into my Dad's machine and everything worked fine. However, when I brought the machine to my Dad's place and plugged in his monitor (Acer 7154e), X crashes no matter what. I tried config xorg.conf with the correct HorizSync and VertRefresh, but it didn't even make any difference.
<snip> Try booting into runlevel 3 and then login as root and do system-config-display --reconfig.
Bests
JS
Jon Savage wrote:
On Mon, 07 Mar 2005 09:38:11 -0500, Benjamin Jiang bjiang_ee@yahoo.ca wrote:
Hi, all,
I installed a fresh copy of FC3 into my Dad's machine and everything worked fine. However, when I brought the machine to my Dad's place and plugged in his monitor (Acer 7154e), X crashes no matter what. I tried config xorg.conf with the correct HorizSync and VertRefresh, but it didn't even make any difference.
<snip> Try booting into runlevel 3 and then login as root and do system-config-display --reconfig.
Bests
JS
Thanks, Jon.
I did that yesterday already and no difference made.
Ben.
----- Message from bjiang_ee@yahoo.ca --------- Date: Mon, 07 Mar 2005 09:53:59 -0500 From: Benjamin Jiang bjiang_ee@yahoo.caReply-To: Discussions about development for the Fedora desktop fedora-desktop-list@redhat.com Subject: Re: X crashes when using a new monitor To: Jon Savage jonathansavage@gmail.com, Discussions about development for the Fedora desktop fedora-desktop-list@redhat.com
Jon Savage wrote:
On Mon, 07 Mar 2005 09:38:11 -0500, Benjamin Jiang bjiang_ee@yahoo.ca wrote:
Hi, all,
I installed a fresh copy of FC3 into my Dad's machine and everything worked fine. However, when I brought the machine to my Dad's place and plugged in his monitor (Acer 7154e), X crashes no matter what. I tried config xorg.conf with the correct HorizSync and VertRefresh, but it didn't even make any difference.
<snip> Try booting into runlevel 3 and then login as root and do system-config-display --reconfig.
Bests
JS
Thanks, Jon.
I did that yesterday already and no difference made.
When booting in to run level 3, log in as either a non privaliged user, or as root and running "startx", if X still crashes you should get some output in the terminal.
Also look through the file /var/log/Xorg.0.log, as that will have some more information that may help us to help you.
Doug
Douglas Furlong wrote:
----- Message from bjiang_ee@yahoo.ca --------- Date: Mon, 07 Mar 2005 09:53:59 -0500 From: Benjamin Jiang bjiang_ee@yahoo.caReply-To: Discussions about development for the Fedora desktop fedora-desktop-list@redhat.com Subject: Re: X crashes when using a new monitor To: Jon Savage jonathansavage@gmail.com, Discussions about development for the Fedora desktop fedora-desktop-list@redhat.com
Jon Savage wrote:
On Mon, 07 Mar 2005 09:38:11 -0500, Benjamin Jiang bjiang_ee@yahoo.ca wrote:
Hi, all,
I installed a fresh copy of FC3 into my Dad's machine and everything worked fine. However, when I brought the machine to my Dad's place and plugged in his monitor (Acer 7154e), X crashes no matter what. I tried config xorg.conf with the correct HorizSync and VertRefresh, but it didn't even make any difference.
<snip> Try booting into runlevel 3 and then login as root and do system-config-display --reconfig.
Bests
JS
Thanks, Jon.
I did that yesterday already and no difference made.
When booting in to run level 3, log in as either a non privaliged user, or as root and running "startx", if X still crashes you should get some output in the terminal.
Also look through the file /var/log/Xorg.0.log, as that will have some more information that may help us to help you.
Doug
Doug, I pasted Xorg.0.log at the end of the first email I sent out.
But, here is it again anyway: Xorg.0.log:
X Window System Version 6.8.1 Release Date: 17 September 2004 X Protocol Version 11, Revision 0, Release 6.8.1 Build Operating System: Linux 2.4.21-14.ELsmp i686 [ELF] Current Operating System: Linux fallsview 2.6.9-1.667 #1 Tue Nov 2 14:41:31 EST 2004 i586 Build Date: 20 October 2004 Build Host: tweety.build.redhat.com
Before reporting problems, check http://wiki.X.Org to make sure that you have the latest version. Module Loader present OS Kernel: Linux version 2.6.9-1.667 (bhcompile@tweety.build.redhat.com) (gcc version 3.4.2 20041017 (Red Hat 3.4.2-6.fc3)) #1 Tue Nov 2 14:41:31 EST 2004 Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Sat Jan 1 02:56:07 2000 (++) Using config file: "xorg.conf.new" (==) ServerLayout "Default Layout" (**) |-->Screen "Screen0" (0) (**) | |-->Monitor "Monitor0" (**) | |-->Device "Videocard0" (**) |-->Input Device "Mouse0" (**) |-->Input Device "Keyboard0" (**) FontPath set to "unix/:7100" (**) RgbPath set to "/usr/X11R6/lib/X11/rgb" (==) ModulePath set to "/usr/X11R6/lib/modules" (WW) Open APM failed (/dev/apm_bios) (No such file or directory) (II) Module ABI versions: X.Org ANSI C Emulation: 0.2 X.Org Video Driver: 0.7 X.Org XInput driver : 0.4 X.Org Server Extension : 0.2 X.Org Font Renderer : 0.4 (II) Loader running on linux (II) LoadModule: "bitmap" (II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.a (II) Module bitmap: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 Module class: X.Org Font Renderer ABI class: X.Org Font Renderer, version 0.4 (II) Loading font Bitmap (II) LoadModule: "pcidata" (II) Loading /usr/X11R6/lib/modules/libpcidata.a (II) Module pcidata: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org Video Driver, version 0.7 (--) using VT number 7
(II) PCI: Probing config type using method 1 (II) PCI: Config type is 1 (II) PCI: stages = 0x03, oldVal1 = 0x00000000, mode1Res1 = 0x80000000 (II) PCI: PCI scan (all values are in hex) (II) PCI: 00:00:0: chip 1106,0598 card 0000,0000 rev 04 class 06,00,00 hdr 00 (II) PCI: 00:01:0: chip 1106,8598 card 0000,0000 rev 00 class 06,04,00 hdr 01 (II) PCI: 00:07:0: chip 1106,0686 card 1106,0000 rev 22 class 06,01,00 hdr 80 (II) PCI: 00:07:1: chip 1106,0571 card 0000,0000 rev 10 class 01,01,8a hdr 00 (II) PCI: 00:07:2: chip 1106,3038 card 0925,1234 rev 10 class 0c,03,00 hdr 00 (II) PCI: 00:07:3: chip 1106,3038 card 0925,1234 rev 10 class 0c,03,00 hdr 00 (II) PCI: 00:07:4: chip 1106,3057 card 0000,0000 rev 30 class 06,00,00 hdr 00 (II) PCI: 00:08:0: chip 122d,50dc card 122d,8000 rev 10 class 04,01,00 hdr 00 (II) PCI: 00:0b:0: chip 10d9,0531 card 15e8,8110 rev 25 class 02,00,00 hdr 00 (II) PCI: 01:00:0: chip 1023,9880 card 1023,9880 rev 3a class 03,00,00 hdr 00 (II) PCI: End of PCI scan (II) Host-to-PCI bridge: (II) Bus 0: bridge is at (0:0:0), (0,0,1), BCTRL: 0x0008 (VGA_EN is set) (II) Bus 0 I/O range: [0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B] (II) Bus 0 non-prefetchable memory range: [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B] (II) Bus 0 prefetchable memory range: [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B] (II) PCI-to-PCI bridge: (II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x000c (VGA_EN is set) (II) Bus 1 non-prefetchable memory range: [0] -1 0 0xd4000000 - 0xd7ffffff (0x4000000) MX[B] (II) PCI-to-ISA bridge: (II) Bus -1: bridge is at (0:7:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set) (II) Host-to-PCI bridge: (II) Bus -1: bridge is at (0:7:4), (-1,-1,1), BCTRL: 0x0008 (VGA_EN is set) (II) Bus -1 I/O range: [0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B] (II) Bus -1 non-prefetchable memory range: [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B] (II) Bus -1 prefetchable memory range: [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B] (--) PCI:*(1:0:0) Trident Microsystems Blade 3D PCI/AGP rev 58, Mem @ 0xd5800000/23, 0xd6000000/17, 0xd5000000/23 (II) Addressable bus resource ranges are [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B] [1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B] (II) OS-reported resource ranges: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] (II) PCI Memory resource overlap reduced 0xd0000000 from 0xd3ffffff to 0xcfffffff (II) Active PCI resource ranges: [0] -1 0 0xd9000000 - 0xd90000ff (0x100) MX[B] [1] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O [2] -1 0 0xd5000000 - 0xd57fffff (0x800000) MX[B](B) [3] -1 0 0xd6000000 - 0xd601ffff (0x20000) MX[B](B) [4] -1 0 0xd5800000 - 0xd5ffffff (0x800000) MX[B](B) [5] -1 0 0x0000e000 - 0x0000e0ff (0x100) IX[B] [6] -1 0 0x0000dc00 - 0x0000dc3f (0x40) IX[B] [7] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B] [8] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B] [9] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B] [10] -1 0 0x0000cc00 - 0x0000cc7f (0x80) IX[B] [11] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B] [12] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B] [13] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B] (II) Active PCI resource ranges after removing overlaps: [0] -1 0 0xd9000000 - 0xd90000ff (0x100) MX[B] [1] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O [2] -1 0 0xd5000000 - 0xd57fffff (0x800000) MX[B](B) [3] -1 0 0xd6000000 - 0xd601ffff (0x20000) MX[B](B) [4] -1 0 0xd5800000 - 0xd5ffffff (0x800000) MX[B](B) [5] -1 0 0x0000e000 - 0x0000e0ff (0x100) IX[B] [6] -1 0 0x0000dc00 - 0x0000dc3f (0x40) IX[B] [7] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B] [8] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B] [9] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B] [10] -1 0 0x0000cc00 - 0x0000cc7f (0x80) IX[B] [11] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B] [12] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B] [13] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B] (II) OS-reported resource ranges after removing overlaps with PCI: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] (II) All system resource ranges: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0xd9000000 - 0xd90000ff (0x100) MX[B] [6] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O [7] -1 0 0xd5000000 - 0xd57fffff (0x800000) MX[B](B) [8] -1 0 0xd6000000 - 0xd601ffff (0x20000) MX[B](B) [9] -1 0 0xd5800000 - 0xd5ffffff (0x800000) MX[B](B) [10] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [11] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [12] -1 0 0x0000e000 - 0x0000e0ff (0x100) IX[B] [13] -1 0 0x0000dc00 - 0x0000dc3f (0x40) IX[B] [14] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B] [15] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B] [16] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B] [17] -1 0 0x0000cc00 - 0x0000cc7f (0x80) IX[B] [18] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B] [19] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B] [20] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B] (II) LoadModule: "dbe" (II) Loading /usr/X11R6/lib/modules/extensions/libdbe.a (II) Module dbe: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 0.2 (II) Loading extension DOUBLE-BUFFER (II) LoadModule: "extmod" (II) Loading /usr/X11R6/lib/modules/extensions/libextmod.a (II) Module extmod: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 0.2 (II) Loading extension SHAPE (II) Loading extension MIT-SUNDRY-NONSTANDARD (II) Loading extension BIG-REQUESTS (II) Loading extension SYNC (II) Loading extension MIT-SCREEN-SAVER (II) Loading extension XC-MISC (II) Loading extension XFree86-VidModeExtension (II) Loading extension XFree86-Misc (II) Loading extension XFree86-DGA (II) Loading extension DPMS (II) Loading extension TOG-CUP (II) Loading extension Extended-Visual-Information (II) Loading extension XVideo (II) Loading extension XVideo-MotionCompensation (II) Loading extension X-Resource (II) LoadModule: "fbdevhw" (II) Loading /usr/X11R6/lib/modules/linux/libfbdevhw.a (II) Module fbdevhw: vendor="X.Org Foundation" compiled for 6.8.1, module version = 0.0.2 ABI class: X.Org Video Driver, version 0.7 (II) LoadModule: "glx" (II) Loading /usr/X11R6/lib/modules/extensions/libglx.a (II) Module glx: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org Server Extension, version 0.2 (II) Loading sub module "GLcore" (II) LoadModule: "GLcore" (II) Loading /usr/X11R6/lib/modules/extensions/libGLcore.a (II) Module GLcore: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org Server Extension, version 0.2 (II) Loading extension GLX (II) LoadModule: "record" (II) Loading /usr/X11R6/lib/modules/extensions/librecord.a (II) Module record: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.13.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 0.2 (II) Loading extension RECORD (II) LoadModule: "freetype" (II) Loading /usr/X11R6/lib/modules/fonts/libfreetype.so (II) Module freetype: vendor="X.Org Foundation & the After X-TT Project" compiled for 6.8.1, module version = 2.1.0 Module class: X.Org Font Renderer ABI class: X.Org Font Renderer, version 0.4 (II) Loading font FreeType (II) LoadModule: "type1" (II) Loading /usr/X11R6/lib/modules/fonts/libtype1.a (II) Module type1: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.2 Module class: X.Org Font Renderer ABI class: X.Org Font Renderer, version 0.4 (II) Loading font Type1 (II) Loading font CID (II) LoadModule: "dri" (II) Loading /usr/X11R6/lib/modules/extensions/libdri.a (II) Module dri: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org Server Extension, version 0.2 (II) Loading sub module "drm" (II) LoadModule: "drm" (II) Loading /usr/X11R6/lib/modules/linux/libdrm.a (II) Module drm: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org Server Extension, version 0.2 (II) Loading extension XFree86-DRI (II) LoadModule: "trident" (II) Loading /usr/X11R6/lib/modules/drivers/trident_drv.o (II) Module trident: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 Module class: X.Org Video Driver ABI class: X.Org Video Driver, version 0.7 (II) LoadModule: "mouse" (II) Loading /usr/X11R6/lib/modules/input/mouse_drv.o (II) Module mouse: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 Module class: X.Org XInput Driver ABI class: X.Org XInput driver, version 0.4 (II) LoadModule: "kbd" (II) Loading /usr/X11R6/lib/modules/input/kbd_drv.o (II) Module kbd: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 Module class: X.Org XInput Driver ABI class: X.Org XInput driver, version 0.4 (II) TRIDENT: driver for Trident chipsets: tvga9000, tvga9000i, tvga8900c, tvga8900d, tvga9200cxr, tgui9400cxi, cyber9320, cyber9388, cyber9397, cyber9397dvd, cyber9520, cyber9525dvd, cyberblade/e4, tgui9420dgi, tgui9440agi, tgui9660, tgui9680, providia9682, providia9685, cyber9382, cyber9385, 3dimage975, 3dimage985, blade3d, cyberbladei7, cyberbladei7d, cyberbladei1, cyberbladei1d, cyberbladeAi1, cyberbladeAi1d, bladeXP, cyberbladeXPAi1, cyberbladeXP4 (II) Primary Device is: PCI 01:00:0 (--) Assigning device section with no busID to primary device (--) Chipset blade3d found (II) resource ranges after xf86ClaimFixedResources() call: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0xd9000000 - 0xd90000ff (0x100) MX[B] [6] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O [7] -1 0 0xd5000000 - 0xd57fffff (0x800000) MX[B](B) [8] -1 0 0xd6000000 - 0xd601ffff (0x20000) MX[B](B) [9] -1 0 0xd5800000 - 0xd5ffffff (0x800000) MX[B](B) [10] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [11] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [12] -1 0 0x0000e000 - 0x0000e0ff (0x100) IX[B] [13] -1 0 0x0000dc00 - 0x0000dc3f (0x40) IX[B] [14] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B] [15] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B] [16] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B] [17] -1 0 0x0000cc00 - 0x0000cc7f (0x80) IX[B] [18] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B] [19] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B] [20] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B] (II) resource ranges after probing: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0xd9000000 - 0xd90000ff (0x100) MX[B] [6] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O [7] -1 0 0xd5000000 - 0xd57fffff (0x800000) MX[B](B) [8] -1 0 0xd6000000 - 0xd601ffff (0x20000) MX[B](B) [9] -1 0 0xd5800000 - 0xd5ffffff (0x800000) MX[B](B) [10] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B] [11] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B] [12] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B] [13] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [14] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [15] -1 0 0x0000e000 - 0x0000e0ff (0x100) IX[B] [16] -1 0 0x0000dc00 - 0x0000dc3f (0x40) IX[B] [17] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B] [18] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B] [19] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B] [20] -1 0 0x0000cc00 - 0x0000cc7f (0x80) IX[B] [21] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B] [22] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B] [23] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B] [24] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B] [25] 0 0 0x000003c0 - 0x000003df (0x20) IS[B] (II) Setting vga for screen 0. (**) TRIDENT(0): Depth 16, (--) framebuffer bpp 16 (II) Loading sub module "vgahw" (II) LoadModule: "vgahw" (II) Loading /usr/X11R6/lib/modules/libvgahw.a (II) Module vgahw: vendor="X.Org Foundation" compiled for 6.8.1, module version = 0.1.0 ABI class: X.Org Video Driver, version 0.7 (II) TRIDENT(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000 (II) Loading sub module "ramdac" (II) LoadModule: "ramdac" (II) Loading /usr/X11R6/lib/modules/libramdac.a (II) Module ramdac: vendor="X.Org Foundation" compiled for 6.8.1, module version = 0.1.0 ABI class: X.Org Video Driver, version 0.7 (==) TRIDENT(0): RGB weight 565 (==) TRIDENT(0): Default visual is TrueColor (==) TRIDENT(0): Using gamma correction (1.0, 1.0, 1.0) (==) TRIDENT(0): Linear framebuffer at 0xD5800000 (--) TRIDENT(0): IO registers at 0xD6000000 (II) Loading sub module "vbe" (II) LoadModule: "vbe" (II) Loading /usr/X11R6/lib/modules/libvbe.a (II) Module vbe: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.1.0 ABI class: X.Org Video Driver, version 0.7 (II) Loading sub module "int10" (II) LoadModule: "int10" (II) Loading /usr/X11R6/lib/modules/linux/libint10.a (II) Module int10: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org Video Driver, version 0.7 (II) TRIDENT(0): initializing int10 (II) TRIDENT(0): Primary V_BIOS segment is: 0xc000 (II) TRIDENT(0): VESA BIOS detected (II) TRIDENT(0): VESA VBE Version 2.0 (II) TRIDENT(0): VESA VBE Total Mem: 8192 kB (II) TRIDENT(0): VESA VBE OEM: Trident Blade 3D (II) TRIDENT(0): VESA VBE OEM Software Rev: 2.0 (II) TRIDENT(0): VESA VBE OEM Vendor: TRIDENT MICROSYSTEMS INC. (II) TRIDENT(0): VESA VBE OEM Product: Blade 3D (II) TRIDENT(0): VESA VBE OEM Product Rev: J 6.4 (38) (II) Loading sub module "ddc" (II) LoadModule: "ddc" (II) Loading /usr/X11R6/lib/modules/libddc.a (II) Module ddc: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org Video Driver, version 0.7 (II) TRIDENT(0): VESA VBE DDC supported (II) TRIDENT(0): VESA VBE DDC Level 2 (II) TRIDENT(0): VESA VBE DDC transfer in appr. 1 sec. (II) TRIDENT(0): VESA VBE DDC read successfully (II) Loading sub module "ddc" (II) LoadModule: "ddc" (II) Reloading /usr/X11R6/lib/modules/libddc.a (II) TRIDENT(0): Manufacturer: API Model: 4536 Serial#: 924 (II) TRIDENT(0): Year: 1997 Week: 26 (II) TRIDENT(0): EDID Version: 1.2 (II) TRIDENT(0): Analog Display Input, Input Voltage Level: 0.700/0.300 V (II) TRIDENT(0): Sync: Separate (II) TRIDENT(0): Max H-Image Size [cm]: horiz.: 27 vert.: 20 (II) TRIDENT(0): Gamma: 2.66 (II) TRIDENT(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display (II) TRIDENT(0): redX: 0.625 redY: 0.340 greenX: 0.284 greenY: 0.600 (II) TRIDENT(0): blueX: 0.149 blueY: 0.064 whiteX: 0.280 whiteY: 0.311 (II) TRIDENT(0): Supported VESA Video Modes: (II) TRIDENT(0): 720x400@70Hz (II) TRIDENT(0): 640x480@60Hz (II) TRIDENT(0): 640x480@72Hz (II) TRIDENT(0): 640x480@75Hz (II) TRIDENT(0): 800x600@60Hz (II) TRIDENT(0): 800x600@72Hz (II) TRIDENT(0): 800x600@75Hz (II) TRIDENT(0): 1024x768@60Hz (II) TRIDENT(0): Manufacturer's mask: 21 (--) TRIDENT(0): Revision is 58 (--) TRIDENT(0): Found Blade3D chip (--) TRIDENT(0): RAM type is SDRAM (--) TRIDENT(0): Using HW cursor (--) TRIDENT(0): VideoRAM: 8192 kByte (--) TRIDENT(0): Memory Clock is 109.77 MHz (==) TRIDENT(0): Min pixel clock is 12 MHz (--) TRIDENT(0): Max pixel clock is 230 MHz (II) TRIDENT(0): Monitor0: Using hsync range of 31.00-60.00 kHz (II) TRIDENT(0): Monitor0: Using vrefresh range of 55.00-90.00 Hz (II) TRIDENT(0): Clock range: 12.00 to 230.00 MHz (II) TRIDENT(0): Not using default mode "320x175" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "320x200" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "360x200" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1024x768" (hsync out of range) (II) TRIDENT(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1152x864" (hsync out of range) (II) TRIDENT(0): Not using default mode "576x432" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1280x960" (hsync out of range) (II) TRIDENT(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1280x1024" (hsync out of range) (II) TRIDENT(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1280x1024" (hsync out of range) (II) TRIDENT(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1280x1024" (hsync out of range) (II) TRIDENT(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1600x1200" (hsync out of range) (II) TRIDENT(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1600x1200" (hsync out of range) (II) TRIDENT(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1600x1200" (hsync out of range) (II) TRIDENT(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1600x1200" (hsync out of range) (II) TRIDENT(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1600x1200" (hsync out of range) (II) TRIDENT(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1792x1344" (hsync out of range) (II) TRIDENT(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1792x1344" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1856x1392" (hsync out of range) (II) TRIDENT(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1856x1392" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "416x312" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "576x384" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1152x864" (hsync out of range) (II) TRIDENT(0): Not using default mode "576x432" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1400x1050" (hsync out of range) (II) TRIDENT(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1400x1050" (hsync out of range) (II) TRIDENT(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1400x1050" (hsync out of range) (II) TRIDENT(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1400x1050" (hsync out of range) (II) TRIDENT(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1600x1024" (hsync out of range) (II) TRIDENT(0): Not using default mode "800x512" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1920x1200" (hsync out of range) (II) TRIDENT(0): Not using default mode "960x600" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1280x960" (width too large for virtual size) (II) TRIDENT(0): Not using default mode "1152x768" (width too large for virtual size) (II) TRIDENT(0): Not using default mode "1024x768" (width too large for virtual size) (II) TRIDENT(0): Not using default mode "1024x768" (width too large for virtual size) (II) TRIDENT(0): Not using default mode "1024x768" (width too large for virtual size) (II) TRIDENT(0): Not using default mode "1024x768" (width too large for virtual size) (II) TRIDENT(0): Not using default mode "832x624" (width too large for virtual size) (--) TRIDENT(0): Virtual size is 800x600 (pitch 800) (**) TRIDENT(0): *Default mode "800x600": 56.3 MHz, 53.7 kHz, 85.1 Hz (II) TRIDENT(0): Modeline "800x600" 56.30 800 832 896 1048 600 601 604 631 +hsync +vsync (**) TRIDENT(0): *Default mode "640x480": 36.0 MHz, 43.3 kHz, 85.0 Hz (II) TRIDENT(0): Modeline "640x480" 36.00 640 696 752 832 480 481 484 509 -hsync -vsync (**) TRIDENT(0): Default mode "800x600": 49.5 MHz, 46.9 kHz, 75.0 Hz (II) TRIDENT(0): Modeline "800x600" 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (**) TRIDENT(0): Default mode "800x600": 50.0 MHz, 48.1 kHz, 72.2 Hz (II) TRIDENT(0): Modeline "800x600" 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (**) TRIDENT(0): Default mode "800x600": 40.0 MHz, 37.9 kHz, 60.3 Hz (II) TRIDENT(0): Modeline "800x600" 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (**) TRIDENT(0): Default mode "800x600": 36.0 MHz, 35.2 kHz, 56.2 Hz (II) TRIDENT(0): Modeline "800x600" 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (**) TRIDENT(0): Default mode "640x480": 31.5 MHz, 37.5 kHz, 75.0 Hz (II) TRIDENT(0): Modeline "640x480" 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (**) TRIDENT(0): Default mode "640x480": 31.5 MHz, 37.9 kHz, 72.8 Hz (II) TRIDENT(0): Modeline "640x480" 31.50 640 664 704 832 480 489 491 520 -hsync -vsync (**) TRIDENT(0): Default mode "640x480": 25.2 MHz, 31.5 kHz, 60.0 Hz (II) TRIDENT(0): Modeline "640x480" 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (**) TRIDENT(0): Default mode "720x400": 35.5 MHz, 37.9 kHz, 85.0 Hz (II) TRIDENT(0): Modeline "720x400" 35.50 720 756 828 936 400 401 404 446 -hsync +vsync (**) TRIDENT(0): Default mode "640x400": 31.5 MHz, 37.9 kHz, 85.1 Hz (II) TRIDENT(0): Modeline "640x400" 31.50 640 672 736 832 400 401 404 445 -hsync +vsync (**) TRIDENT(0): Default mode "640x350": 31.5 MHz, 37.9 kHz, 85.1 Hz (II) TRIDENT(0): Modeline "640x350" 31.50 640 672 736 832 350 382 385 445 +hsync -vsync (**) TRIDENT(0): Display dimensions: (270, 200) mm (**) TRIDENT(0): DPI set to (75, 76) (II) Loading sub module "fb" (II) LoadModule: "fb" (II) Loading /usr/X11R6/lib/modules/libfb.a (II) Module fb: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org ANSI C Emulation, version 0.2 (II) Loading sub module "i2c" (II) LoadModule: "i2c" (II) Loading /usr/X11R6/lib/modules/libi2c.a (II) Module i2c: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.2.0 ABI class: X.Org Video Driver, version 0.7 (II) Loading sub module "xaa" (II) LoadModule: "xaa" (II) Loading /usr/X11R6/lib/modules/libxaa.a (II) Module xaa: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.2.0 ABI class: X.Org Video Driver, version 0.7
*** If unresolved symbols were reported above, they might not *** be the reason for the server aborting.
Fatal server error: Caught signal 11. Server aborting
Please consult the The X.Org Foundation support at http://wiki.X.Org for help. Please also check the log file at "/var/log/Xorg.0.log" for additional information.
Ben.
man, 07.03.2005 kl. 16.40 skrev Benjamin Jiang:
Douglas Furlong wrote:
----- Message from bjiang_ee@yahoo.ca --------- Date: Mon, 07 Mar 2005 09:53:59 -0500 From: Benjamin Jiang bjiang_ee@yahoo.caReply-To: Discussions about development for the Fedora desktop fedora-desktop-list@redhat.com Subject: Re: X crashes when using a new monitor To: Jon Savage jonathansavage@gmail.com, Discussions about development for the Fedora desktop fedora-desktop-list@redhat.com
Jon Savage wrote:
On Mon, 07 Mar 2005 09:38:11 -0500, Benjamin Jiang bjiang_ee@yahoo.ca wrote:
Hi, all,
I installed a fresh copy of FC3 into my Dad's machine and everything worked fine. However, when I brought the machine to my Dad's place and plugged in his monitor (Acer 7154e), X crashes no matter what. I tried config xorg.conf with the correct HorizSync and VertRefresh, but it didn't even make any difference.
<snip> Try booting into runlevel 3 and then login as root and do system-config-display --reconfig.
Bests
JS
Thanks, Jon.
I did that yesterday already and no difference made.
When booting in to run level 3, log in as either a non privaliged user, or as root and running "startx", if X still crashes you should get some output in the terminal.
Also look through the file /var/log/Xorg.0.log, as that will have some more information that may help us to help you.
Doug
Doug, I pasted Xorg.0.log at the end of the first email I sent out.
But, here is it again anyway: Xorg.0.log:
X Window System Version 6.8.1 Release Date: 17 September 2004 X Protocol Version 11, Revision 0, Release 6.8.1 Build Operating System: Linux 2.4.21-14.ELsmp i686 [ELF] Current Operating System: Linux fallsview 2.6.9-1.667 #1 Tue Nov 2 14:41:31 EST 2004 i586 Build Date: 20 October 2004 Build Host: tweety.build.redhat.com
Before reporting problems, check http://wiki.X.Org to make sure that you have the latest version.
Module Loader present OS Kernel: Linux version 2.6.9-1.667 (bhcompile@tweety.build.redhat.com) (gcc version 3.4.2 20041017 (Red Hat 3.4.2-6.fc3)) #1 Tue Nov 2 14:41:31 EST 2004 Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Sat Jan 1 02:56:07 2000 (++) Using config file: "xorg.conf.new" (==) ServerLayout "Default Layout" (**) |-->Screen "Screen0" (0) (**) | |-->Monitor "Monitor0" (**) | |-->Device "Videocard0" (**) |-->Input Device "Mouse0" (**) |-->Input Device "Keyboard0" (**) FontPath set to "unix/:7100" (**) RgbPath set to "/usr/X11R6/lib/X11/rgb" (==) ModulePath set to "/usr/X11R6/lib/modules" (WW) Open APM failed (/dev/apm_bios) (No such file or directory) (II) Module ABI versions: X.Org ANSI C Emulation: 0.2 X.Org Video Driver: 0.7 X.Org XInput driver : 0.4 X.Org Server Extension : 0.2 X.Org Font Renderer : 0.4 (II) Loader running on linux (II) LoadModule: "bitmap" (II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.a (II) Module bitmap: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 Module class: X.Org Font Renderer ABI class: X.Org Font Renderer, version 0.4 (II) Loading font Bitmap (II) LoadModule: "pcidata" (II) Loading /usr/X11R6/lib/modules/libpcidata.a (II) Module pcidata: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org Video Driver, version 0.7 (--) using VT number 7
(II) PCI: Probing config type using method 1 (II) PCI: Config type is 1 (II) PCI: stages = 0x03, oldVal1 = 0x00000000, mode1Res1 = 0x80000000 (II) PCI: PCI scan (all values are in hex) (II) PCI: 00:00:0: chip 1106,0598 card 0000,0000 rev 04 class 06,00,00 hdr 00 (II) PCI: 00:01:0: chip 1106,8598 card 0000,0000 rev 00 class 06,04,00 hdr 01 (II) PCI: 00:07:0: chip 1106,0686 card 1106,0000 rev 22 class 06,01,00 hdr 80 (II) PCI: 00:07:1: chip 1106,0571 card 0000,0000 rev 10 class 01,01,8a hdr 00 (II) PCI: 00:07:2: chip 1106,3038 card 0925,1234 rev 10 class 0c,03,00 hdr 00 (II) PCI: 00:07:3: chip 1106,3038 card 0925,1234 rev 10 class 0c,03,00 hdr 00 (II) PCI: 00:07:4: chip 1106,3057 card 0000,0000 rev 30 class 06,00,00 hdr 00 (II) PCI: 00:08:0: chip 122d,50dc card 122d,8000 rev 10 class 04,01,00 hdr 00 (II) PCI: 00:0b:0: chip 10d9,0531 card 15e8,8110 rev 25 class 02,00,00 hdr 00 (II) PCI: 01:00:0: chip 1023,9880 card 1023,9880 rev 3a class 03,00,00 hdr 00 (II) PCI: End of PCI scan (II) Host-to-PCI bridge: (II) Bus 0: bridge is at (0:0:0), (0,0,1), BCTRL: 0x0008 (VGA_EN is set) (II) Bus 0 I/O range: [0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B] (II) Bus 0 non-prefetchable memory range: [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B] (II) Bus 0 prefetchable memory range: [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B] (II) PCI-to-PCI bridge: (II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x000c (VGA_EN is set) (II) Bus 1 non-prefetchable memory range: [0] -1 0 0xd4000000 - 0xd7ffffff (0x4000000) MX[B] (II) PCI-to-ISA bridge: (II) Bus -1: bridge is at (0:7:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set) (II) Host-to-PCI bridge: (II) Bus -1: bridge is at (0:7:4), (-1,-1,1), BCTRL: 0x0008 (VGA_EN is set) (II) Bus -1 I/O range: [0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B] (II) Bus -1 non-prefetchable memory range: [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B] (II) Bus -1 prefetchable memory range: [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B] (--) PCI:*(1:0:0) Trident Microsystems Blade 3D PCI/AGP rev 58, Mem @ 0xd5800000/23, 0xd6000000/17, 0xd5000000/23 (II) Addressable bus resource ranges are [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B] [1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B] (II) OS-reported resource ranges: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] (II) PCI Memory resource overlap reduced 0xd0000000 from 0xd3ffffff to 0xcfffffff (II) Active PCI resource ranges: [0] -1 0 0xd9000000 - 0xd90000ff (0x100) MX[B] [1] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O [2] -1 0 0xd5000000 - 0xd57fffff (0x800000) MX[B](B) [3] -1 0 0xd6000000 - 0xd601ffff (0x20000) MX[B](B) [4] -1 0 0xd5800000 - 0xd5ffffff (0x800000) MX[B](B) [5] -1 0 0x0000e000 - 0x0000e0ff (0x100) IX[B] [6] -1 0 0x0000dc00 - 0x0000dc3f (0x40) IX[B] [7] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B] [8] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B] [9] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B] [10] -1 0 0x0000cc00 - 0x0000cc7f (0x80) IX[B] [11] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B] [12] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B] [13] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B] (II) Active PCI resource ranges after removing overlaps: [0] -1 0 0xd9000000 - 0xd90000ff (0x100) MX[B] [1] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O [2] -1 0 0xd5000000 - 0xd57fffff (0x800000) MX[B](B) [3] -1 0 0xd6000000 - 0xd601ffff (0x20000) MX[B](B) [4] -1 0 0xd5800000 - 0xd5ffffff (0x800000) MX[B](B) [5] -1 0 0x0000e000 - 0x0000e0ff (0x100) IX[B] [6] -1 0 0x0000dc00 - 0x0000dc3f (0x40) IX[B] [7] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B] [8] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B] [9] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B] [10] -1 0 0x0000cc00 - 0x0000cc7f (0x80) IX[B] [11] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B] [12] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B] [13] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B] (II) OS-reported resource ranges after removing overlaps with PCI: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] (II) All system resource ranges: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0xd9000000 - 0xd90000ff (0x100) MX[B] [6] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O [7] -1 0 0xd5000000 - 0xd57fffff (0x800000) MX[B](B) [8] -1 0 0xd6000000 - 0xd601ffff (0x20000) MX[B](B) [9] -1 0 0xd5800000 - 0xd5ffffff (0x800000) MX[B](B) [10] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [11] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [12] -1 0 0x0000e000 - 0x0000e0ff (0x100) IX[B] [13] -1 0 0x0000dc00 - 0x0000dc3f (0x40) IX[B] [14] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B] [15] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B] [16] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B] [17] -1 0 0x0000cc00 - 0x0000cc7f (0x80) IX[B] [18] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B] [19] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B] [20] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B] (II) LoadModule: "dbe" (II) Loading /usr/X11R6/lib/modules/extensions/libdbe.a (II) Module dbe: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 0.2 (II) Loading extension DOUBLE-BUFFER (II) LoadModule: "extmod" (II) Loading /usr/X11R6/lib/modules/extensions/libextmod.a (II) Module extmod: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 0.2 (II) Loading extension SHAPE (II) Loading extension MIT-SUNDRY-NONSTANDARD (II) Loading extension BIG-REQUESTS (II) Loading extension SYNC (II) Loading extension MIT-SCREEN-SAVER (II) Loading extension XC-MISC (II) Loading extension XFree86-VidModeExtension (II) Loading extension XFree86-Misc (II) Loading extension XFree86-DGA (II) Loading extension DPMS (II) Loading extension TOG-CUP (II) Loading extension Extended-Visual-Information (II) Loading extension XVideo (II) Loading extension XVideo-MotionCompensation (II) Loading extension X-Resource (II) LoadModule: "fbdevhw" (II) Loading /usr/X11R6/lib/modules/linux/libfbdevhw.a (II) Module fbdevhw: vendor="X.Org Foundation" compiled for 6.8.1, module version = 0.0.2 ABI class: X.Org Video Driver, version 0.7 (II) LoadModule: "glx" (II) Loading /usr/X11R6/lib/modules/extensions/libglx.a (II) Module glx: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org Server Extension, version 0.2 (II) Loading sub module "GLcore" (II) LoadModule: "GLcore" (II) Loading /usr/X11R6/lib/modules/extensions/libGLcore.a (II) Module GLcore: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org Server Extension, version 0.2 (II) Loading extension GLX (II) LoadModule: "record" (II) Loading /usr/X11R6/lib/modules/extensions/librecord.a (II) Module record: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.13.0 Module class: X.Org Server Extension ABI class: X.Org Server Extension, version 0.2 (II) Loading extension RECORD (II) LoadModule: "freetype" (II) Loading /usr/X11R6/lib/modules/fonts/libfreetype.so (II) Module freetype: vendor="X.Org Foundation & the After X-TT Project" compiled for 6.8.1, module version = 2.1.0 Module class: X.Org Font Renderer ABI class: X.Org Font Renderer, version 0.4 (II) Loading font FreeType (II) LoadModule: "type1" (II) Loading /usr/X11R6/lib/modules/fonts/libtype1.a (II) Module type1: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.2 Module class: X.Org Font Renderer ABI class: X.Org Font Renderer, version 0.4 (II) Loading font Type1 (II) Loading font CID (II) LoadModule: "dri" (II) Loading /usr/X11R6/lib/modules/extensions/libdri.a (II) Module dri: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org Server Extension, version 0.2 (II) Loading sub module "drm" (II) LoadModule: "drm" (II) Loading /usr/X11R6/lib/modules/linux/libdrm.a (II) Module drm: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org Server Extension, version 0.2 (II) Loading extension XFree86-DRI (II) LoadModule: "trident" (II) Loading /usr/X11R6/lib/modules/drivers/trident_drv.o (II) Module trident: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 Module class: X.Org Video Driver ABI class: X.Org Video Driver, version 0.7 (II) LoadModule: "mouse" (II) Loading /usr/X11R6/lib/modules/input/mouse_drv.o (II) Module mouse: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 Module class: X.Org XInput Driver ABI class: X.Org XInput driver, version 0.4 (II) LoadModule: "kbd" (II) Loading /usr/X11R6/lib/modules/input/kbd_drv.o (II) Module kbd: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 Module class: X.Org XInput Driver ABI class: X.Org XInput driver, version 0.4 (II) TRIDENT: driver for Trident chipsets: tvga9000, tvga9000i, tvga8900c, tvga8900d, tvga9200cxr, tgui9400cxi, cyber9320, cyber9388, cyber9397, cyber9397dvd, cyber9520, cyber9525dvd, cyberblade/e4, tgui9420dgi, tgui9440agi, tgui9660, tgui9680, providia9682, providia9685, cyber9382, cyber9385, 3dimage975, 3dimage985, blade3d, cyberbladei7, cyberbladei7d, cyberbladei1, cyberbladei1d, cyberbladeAi1, cyberbladeAi1d, bladeXP, cyberbladeXPAi1, cyberbladeXP4 (II) Primary Device is: PCI 01:00:0 (--) Assigning device section with no busID to primary device (--) Chipset blade3d found (II) resource ranges after xf86ClaimFixedResources() call: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0xd9000000 - 0xd90000ff (0x100) MX[B] [6] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O [7] -1 0 0xd5000000 - 0xd57fffff (0x800000) MX[B](B) [8] -1 0 0xd6000000 - 0xd601ffff (0x20000) MX[B](B) [9] -1 0 0xd5800000 - 0xd5ffffff (0x800000) MX[B](B) [10] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [11] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [12] -1 0 0x0000e000 - 0x0000e0ff (0x100) IX[B] [13] -1 0 0x0000dc00 - 0x0000dc3f (0x40) IX[B] [14] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B] [15] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B] [16] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B] [17] -1 0 0x0000cc00 - 0x0000cc7f (0x80) IX[B] [18] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B] [19] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B] [20] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B] (II) resource ranges after probing: [0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B) [1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B) [2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B] [3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B] [4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B] [5] -1 0 0xd9000000 - 0xd90000ff (0x100) MX[B] [6] -1 0 0xd0000000 - 0xcfffffff (0x0) MX[B]O [7] -1 0 0xd5000000 - 0xd57fffff (0x800000) MX[B](B) [8] -1 0 0xd6000000 - 0xd601ffff (0x20000) MX[B](B) [9] -1 0 0xd5800000 - 0xd5ffffff (0x800000) MX[B](B) [10] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B] [11] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B] [12] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B] [13] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B] [14] -1 0 0x00000000 - 0x000000ff (0x100) IX[B] [15] -1 0 0x0000e000 - 0x0000e0ff (0x100) IX[B] [16] -1 0 0x0000dc00 - 0x0000dc3f (0x40) IX[B] [17] -1 0 0x0000d800 - 0x0000d807 (0x8) IX[B] [18] -1 0 0x0000d400 - 0x0000d403 (0x4) IX[B] [19] -1 0 0x0000d000 - 0x0000d007 (0x8) IX[B] [20] -1 0 0x0000cc00 - 0x0000cc7f (0x80) IX[B] [21] -1 0 0x0000c800 - 0x0000c81f (0x20) IX[B] [22] -1 0 0x0000c400 - 0x0000c41f (0x20) IX[B] [23] -1 0 0x0000c000 - 0x0000c00f (0x10) IX[B] [24] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B] [25] 0 0 0x000003c0 - 0x000003df (0x20) IS[B] (II) Setting vga for screen 0. (**) TRIDENT(0): Depth 16, (--) framebuffer bpp 16 (II) Loading sub module "vgahw" (II) LoadModule: "vgahw" (II) Loading /usr/X11R6/lib/modules/libvgahw.a (II) Module vgahw: vendor="X.Org Foundation" compiled for 6.8.1, module version = 0.1.0 ABI class: X.Org Video Driver, version 0.7 (II) TRIDENT(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000 (II) Loading sub module "ramdac" (II) LoadModule: "ramdac" (II) Loading /usr/X11R6/lib/modules/libramdac.a (II) Module ramdac: vendor="X.Org Foundation" compiled for 6.8.1, module version = 0.1.0 ABI class: X.Org Video Driver, version 0.7 (==) TRIDENT(0): RGB weight 565 (==) TRIDENT(0): Default visual is TrueColor (==) TRIDENT(0): Using gamma correction (1.0, 1.0, 1.0) (==) TRIDENT(0): Linear framebuffer at 0xD5800000 (--) TRIDENT(0): IO registers at 0xD6000000 (II) Loading sub module "vbe" (II) LoadModule: "vbe" (II) Loading /usr/X11R6/lib/modules/libvbe.a (II) Module vbe: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.1.0 ABI class: X.Org Video Driver, version 0.7 (II) Loading sub module "int10" (II) LoadModule: "int10" (II) Loading /usr/X11R6/lib/modules/linux/libint10.a (II) Module int10: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org Video Driver, version 0.7 (II) TRIDENT(0): initializing int10 (II) TRIDENT(0): Primary V_BIOS segment is: 0xc000 (II) TRIDENT(0): VESA BIOS detected (II) TRIDENT(0): VESA VBE Version 2.0 (II) TRIDENT(0): VESA VBE Total Mem: 8192 kB (II) TRIDENT(0): VESA VBE OEM: Trident Blade 3D (II) TRIDENT(0): VESA VBE OEM Software Rev: 2.0 (II) TRIDENT(0): VESA VBE OEM Vendor: TRIDENT MICROSYSTEMS INC. (II) TRIDENT(0): VESA VBE OEM Product: Blade 3D (II) TRIDENT(0): VESA VBE OEM Product Rev: J 6.4 (38) (II) Loading sub module "ddc" (II) LoadModule: "ddc" (II) Loading /usr/X11R6/lib/modules/libddc.a (II) Module ddc: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org Video Driver, version 0.7 (II) TRIDENT(0): VESA VBE DDC supported (II) TRIDENT(0): VESA VBE DDC Level 2 (II) TRIDENT(0): VESA VBE DDC transfer in appr. 1 sec. (II) TRIDENT(0): VESA VBE DDC read successfully (II) Loading sub module "ddc" (II) LoadModule: "ddc" (II) Reloading /usr/X11R6/lib/modules/libddc.a (II) TRIDENT(0): Manufacturer: API Model: 4536 Serial#: 924 (II) TRIDENT(0): Year: 1997 Week: 26 (II) TRIDENT(0): EDID Version: 1.2 (II) TRIDENT(0): Analog Display Input, Input Voltage Level: 0.700/0.300 V (II) TRIDENT(0): Sync: Separate (II) TRIDENT(0): Max H-Image Size [cm]: horiz.: 27 vert.: 20 (II) TRIDENT(0): Gamma: 2.66 (II) TRIDENT(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display (II) TRIDENT(0): redX: 0.625 redY: 0.340 greenX: 0.284 greenY: 0.600 (II) TRIDENT(0): blueX: 0.149 blueY: 0.064 whiteX: 0.280 whiteY: 0.311 (II) TRIDENT(0): Supported VESA Video Modes: (II) TRIDENT(0): 720x400@70Hz (II) TRIDENT(0): 640x480@60Hz (II) TRIDENT(0): 640x480@72Hz (II) TRIDENT(0): 640x480@75Hz (II) TRIDENT(0): 800x600@60Hz (II) TRIDENT(0): 800x600@72Hz (II) TRIDENT(0): 800x600@75Hz (II) TRIDENT(0): 1024x768@60Hz (II) TRIDENT(0): Manufacturer's mask: 21 (--) TRIDENT(0): Revision is 58 (--) TRIDENT(0): Found Blade3D chip (--) TRIDENT(0): RAM type is SDRAM (--) TRIDENT(0): Using HW cursor (--) TRIDENT(0): VideoRAM: 8192 kByte (--) TRIDENT(0): Memory Clock is 109.77 MHz (==) TRIDENT(0): Min pixel clock is 12 MHz (--) TRIDENT(0): Max pixel clock is 230 MHz (II) TRIDENT(0): Monitor0: Using hsync range of 31.00-60.00 kHz (II) TRIDENT(0): Monitor0: Using vrefresh range of 55.00-90.00 Hz (II) TRIDENT(0): Clock range: 12.00 to 230.00 MHz (II) TRIDENT(0): Not using default mode "320x175" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "320x200" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "360x200" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1024x768" (hsync out of range) (II) TRIDENT(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1152x864" (hsync out of range) (II) TRIDENT(0): Not using default mode "576x432" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1280x960" (hsync out of range) (II) TRIDENT(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1280x1024" (hsync out of range) (II) TRIDENT(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1280x1024" (hsync out of range) (II) TRIDENT(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1280x1024" (hsync out of range) (II) TRIDENT(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1600x1200" (hsync out of range) (II) TRIDENT(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1600x1200" (hsync out of range) (II) TRIDENT(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1600x1200" (hsync out of range) (II) TRIDENT(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1600x1200" (hsync out of range) (II) TRIDENT(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1600x1200" (hsync out of range) (II) TRIDENT(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1792x1344" (hsync out of range) (II) TRIDENT(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1792x1344" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1856x1392" (hsync out of range) (II) TRIDENT(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1856x1392" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "416x312" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "576x384" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1152x864" (hsync out of range) (II) TRIDENT(0): Not using default mode "576x432" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1400x1050" (hsync out of range) (II) TRIDENT(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1400x1050" (hsync out of range) (II) TRIDENT(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1400x1050" (hsync out of range) (II) TRIDENT(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1400x1050" (hsync out of range) (II) TRIDENT(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1600x1024" (hsync out of range) (II) TRIDENT(0): Not using default mode "800x512" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1920x1200" (hsync out of range) (II) TRIDENT(0): Not using default mode "960x600" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan) (II) TRIDENT(0): Not using default mode "1280x960" (width too large for virtual size) (II) TRIDENT(0): Not using default mode "1152x768" (width too large for virtual size) (II) TRIDENT(0): Not using default mode "1024x768" (width too large for virtual size) (II) TRIDENT(0): Not using default mode "1024x768" (width too large for virtual size) (II) TRIDENT(0): Not using default mode "1024x768" (width too large for virtual size) (II) TRIDENT(0): Not using default mode "1024x768" (width too large for virtual size) (II) TRIDENT(0): Not using default mode "832x624" (width too large for virtual size) (--) TRIDENT(0): Virtual size is 800x600 (pitch 800) (**) TRIDENT(0): *Default mode "800x600": 56.3 MHz, 53.7 kHz, 85.1 Hz (II) TRIDENT(0): Modeline "800x600" 56.30 800 832 896 1048 600 601 604 631 +hsync +vsync (**) TRIDENT(0): *Default mode "640x480": 36.0 MHz, 43.3 kHz, 85.0 Hz (II) TRIDENT(0): Modeline "640x480" 36.00 640 696 752 832 480 481 484 509 -hsync -vsync (**) TRIDENT(0): Default mode "800x600": 49.5 MHz, 46.9 kHz, 75.0 Hz (II) TRIDENT(0): Modeline "800x600" 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (**) TRIDENT(0): Default mode "800x600": 50.0 MHz, 48.1 kHz, 72.2 Hz (II) TRIDENT(0): Modeline "800x600" 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (**) TRIDENT(0): Default mode "800x600": 40.0 MHz, 37.9 kHz, 60.3 Hz (II) TRIDENT(0): Modeline "800x600" 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (**) TRIDENT(0): Default mode "800x600": 36.0 MHz, 35.2 kHz, 56.2 Hz (II) TRIDENT(0): Modeline "800x600" 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (**) TRIDENT(0): Default mode "640x480": 31.5 MHz, 37.5 kHz, 75.0 Hz (II) TRIDENT(0): Modeline "640x480" 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (**) TRIDENT(0): Default mode "640x480": 31.5 MHz, 37.9 kHz, 72.8 Hz (II) TRIDENT(0): Modeline "640x480" 31.50 640 664 704 832 480 489 491 520 -hsync -vsync (**) TRIDENT(0): Default mode "640x480": 25.2 MHz, 31.5 kHz, 60.0 Hz (II) TRIDENT(0): Modeline "640x480" 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (**) TRIDENT(0): Default mode "720x400": 35.5 MHz, 37.9 kHz, 85.0 Hz (II) TRIDENT(0): Modeline "720x400" 35.50 720 756 828 936 400 401 404 446 -hsync +vsync (**) TRIDENT(0): Default mode "640x400": 31.5 MHz, 37.9 kHz, 85.1 Hz (II) TRIDENT(0): Modeline "640x400" 31.50 640 672 736 832 400 401 404 445 -hsync +vsync (**) TRIDENT(0): Default mode "640x350": 31.5 MHz, 37.9 kHz, 85.1 Hz (II) TRIDENT(0): Modeline "640x350" 31.50 640 672 736 832 350 382 385 445 +hsync -vsync (**) TRIDENT(0): Display dimensions: (270, 200) mm (**) TRIDENT(0): DPI set to (75, 76) (II) Loading sub module "fb" (II) LoadModule: "fb" (II) Loading /usr/X11R6/lib/modules/libfb.a (II) Module fb: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.0.0 ABI class: X.Org ANSI C Emulation, version 0.2 (II) Loading sub module "i2c" (II) LoadModule: "i2c" (II) Loading /usr/X11R6/lib/modules/libi2c.a (II) Module i2c: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.2.0 ABI class: X.Org Video Driver, version 0.7 (II) Loading sub module "xaa" (II) LoadModule: "xaa" (II) Loading /usr/X11R6/lib/modules/libxaa.a (II) Module xaa: vendor="X.Org Foundation" compiled for 6.8.1, module version = 1.2.0 ABI class: X.Org Video Driver, version 0.7
*** If unresolved symbols were reported above, they might not *** be the reason for the server aborting.
Fatal server error: Caught signal 11. Server aborting
Please consult the The X.Org Foundation support at http://wiki.X.Org for help. Please also check the log file at "/var/log/Xorg.0.log" for additional information.
Ben.
My experience is that if X sends the wrong sync to a monitor, all that happens is that the monitor shows a borked picture, or nothing at all exept an error message. X doesn't crash...
----- Message from kyrre@solution-forge.net --------- Date: Mon, 07 Mar 2005 18:51:56 +0100 From: Kyrre Ness Sjobak kyrre@solution-forge.netReply-To: Discussions about development for the Fedora desktop fedora-desktop-list@redhat.com Subject: Re: X crashes when using a new monitor To: Discussions about development for the Fedora desktop fedora-desktop-list@redhat.com
man, 07.03.2005 kl. 16.40 skrev Benjamin Jiang:
Douglas Furlong wrote:
----- Message from bjiang_ee@yahoo.ca --------- Date: Mon, 07 Mar 2005 09:53:59 -0500 From: Benjamin Jiang bjiang_ee@yahoo.caReply-To: Discussions about development for the Fedora desktop fedora-desktop-list@redhat.com Subject: Re: X crashes when using a new monitor To: Jon Savage jonathansavage@gmail.com, Discussions about development for the Fedora desktop fedora-desktop-list@redhat.com
Jon Savage wrote:
On Mon, 07 Mar 2005 09:38:11 -0500, Benjamin Jiang bjiang_ee@yahoo.ca wrote:
Hi, all,
I installed a fresh copy of FC3 into my Dad's machine and everything worked fine. However, when I brought the machine to my Dad's place and plugged in his monitor (Acer 7154e), X crashes no matter what. I tried config xorg.conf with the correct HorizSync and VertRefresh, but it didn't even make any difference.
<snip> Try booting into runlevel 3 and then login as root and do system-config-display --reconfig.
Bests
JS
Thanks, Jon.
I did that yesterday already and no difference made.
When booting in to run level 3, log in as either a non privaliged user, or as root and running "startx", if X still crashes you should get some output in the terminal.
Also look through the file /var/log/Xorg.0.log, as that will have some more information that may help us to help you.
Doug
Doug, I pasted Xorg.0.log at the end of the first email I sent out.
But, here is it again anyway: Xorg.0.log:
My experience is that if X sends the wrong sync to a monitor, all that happens is that the monitor shows a borked picture, or nothing at all exept an error message. X doesn't crash...
My expearience is slightly different.
If X fails to start due to refresh rate issues, then it will fail to start, not "crash" just will stop trying to load.
However this error seems to suggest that it did "crash".
It could be due to a damaged hard disk in transit? Causing a problem with some of the libraries?
Douglas Furlong wrote:
----- Message from kyrre@solution-forge.net --------- Date: Mon, 07 Mar 2005 18:51:56 +0100 From: Kyrre Ness Sjobak kyrre@solution-forge.netReply-To: Discussions about development for the Fedora desktop fedora-desktop-list@redhat.com Subject: Re: X crashes when using a new monitor To: Discussions about development for the Fedora desktop fedora-desktop-list@redhat.com
man, 07.03.2005 kl. 16.40 skrev Benjamin Jiang:
Douglas Furlong wrote:
----- Message from bjiang_ee@yahoo.ca --------- Date: Mon, 07
Mar 2005
09:53:59 -0500 From: Benjamin Jiang bjiang_ee@yahoo.caReply-To: Discussions about development for the Fedora desktop fedora-desktop-list@redhat.com Subject: Re: X crashes when using
a new
monitor To: Jon Savage jonathansavage@gmail.com,
Discussions about
development for the Fedora desktop fedora-desktop-list@redhat.com
Jon Savage wrote:
On Mon, 07 Mar 2005 09:38:11 -0500, Benjamin Jiang bjiang_ee@yahoo.ca wrote:
> Hi, all, > > I installed a fresh copy of FC3 into my Dad's machine and
everything
> worked fine. However, when I brought the machine to my Dad's
place and
> plugged in his monitor (Acer 7154e), X crashes no matter what.
I tried
> config xorg.conf with the correct HorizSync and VertRefresh,
but it
> didn't even make any difference. >
<snip> Try booting into runlevel 3 and then login as root and do system-config-display --reconfig.
Bests
JS
Thanks, Jon.
I did that yesterday already and no difference made.
When booting in to run level 3, log in as either a non privaliged user, or as root and running "startx", if X still crashes you should get some output in the terminal.
Also look through the file /var/log/Xorg.0.log, as that will have
some
more information that may help us to help you.
Doug
Doug, I pasted Xorg.0.log at the end of the first email I sent out.
But, here is it again anyway: Xorg.0.log:
My experience is that if X sends the wrong sync to a monitor, all that happens is that the monitor shows a borked picture, or nothing at all exept an error message. X doesn't crash...
My expearience is slightly different.
If X fails to start due to refresh rate issues, then it will fail to start, not "crash" just will stop trying to load.
However this error seems to suggest that it did "crash".
It could be due to a damaged hard disk in transit? Causing a problem with some of the libraries?
Let me try to copy the whole /usr/X11R6 directory from a working FC3 machne then. Is that the only directory? Maybe /usr/lib/X11 as weel?
Ben.
man, 07.03.2005 kl. 20.39 skrev Benjamin Jiang:
Douglas Furlong wrote:
----- Message from kyrre@solution-forge.net --------- Date: Mon, 07 Mar 2005 18:51:56 +0100 From: Kyrre Ness Sjobak kyrre@solution-forge.netReply-To: Discussions about development for the Fedora desktop fedora-desktop-list@redhat.com Subject: Re: X crashes when using a new monitor To: Discussions about development for the Fedora desktop fedora-desktop-list@redhat.com
man, 07.03.2005 kl. 16.40 skrev Benjamin Jiang:
Douglas Furlong wrote:
----- Message from bjiang_ee@yahoo.ca --------- Date: Mon, 07
Mar 2005
09:53:59 -0500 From: Benjamin Jiang bjiang_ee@yahoo.caReply-To: Discussions about development for the Fedora desktop fedora-desktop-list@redhat.com Subject: Re: X crashes when using
a new
monitor To: Jon Savage jonathansavage@gmail.com,
Discussions about
development for the Fedora desktop fedora-desktop-list@redhat.com
Jon Savage wrote:
> On Mon, 07 Mar 2005 09:38:11 -0500, Benjamin Jiang > bjiang_ee@yahoo.ca wrote: > >> Hi, all, >> >> I installed a fresh copy of FC3 into my Dad's machine and
everything
>> worked fine. However, when I brought the machine to my Dad's
place and
>> plugged in his monitor (Acer 7154e), X crashes no matter what.
I tried
>> config xorg.conf with the correct HorizSync and VertRefresh,
but it
>> didn't even make any difference. >> > <snip> > Try booting into runlevel 3 and then > login as root and do system-config-display --reconfig. > > Bests > > JS > > Thanks, Jon.
I did that yesterday already and no difference made.
When booting in to run level 3, log in as either a non privaliged user, or as root and running "startx", if X still crashes you should get some output in the terminal.
Also look through the file /var/log/Xorg.0.log, as that will have
some
more information that may help us to help you.
Doug
Doug, I pasted Xorg.0.log at the end of the first email I sent out.
But, here is it again anyway: Xorg.0.log:
My experience is that if X sends the wrong sync to a monitor, all that happens is that the monitor shows a borked picture, or nothing at all exept an error message. X doesn't crash...
My expearience is slightly different.
If X fails to start due to refresh rate issues, then it will fail to start, not "crash" just will stop trying to load.
However this error seems to suggest that it did "crash".
It could be due to a damaged hard disk in transit? Causing a problem with some of the libraries?
Let me try to copy the whole /usr/X11R6 directory from a working FC3 machne then. Is that the only directory? Maybe /usr/lib/X11 as weel?
Ben.
Urk?!? If you are running slackware, go ahead. Since you are running fedora, i would probably more suggest to remove xorg by rpm and then reinstall it (maybe just use --nodeps when removing it, as you are going to plug it right back in again) from known good media
Benjamin Jiang wrote:
Douglas Furlong wrote:
----- Message from kyrre@solution-forge.net --------- Date: Mon, 07 Mar 2005 18:51:56 +0100 From: Kyrre Ness Sjobak kyrre@solution-forge.netReply-To: Discussions about development for the Fedora desktop fedora-desktop-list@redhat.com Subject: Re: X crashes when using a new monitor To: Discussions about development for the Fedora desktop fedora-desktop-list@redhat.com
man, 07.03.2005 kl. 16.40 skrev Benjamin Jiang:
Douglas Furlong wrote:
----- Message from bjiang_ee@yahoo.ca --------- Date: Mon, 07
Mar 2005
09:53:59 -0500 From: Benjamin Jiang bjiang_ee@yahoo.caReply-To: Discussions about development for the Fedora desktop fedora-desktop-list@redhat.com Subject: Re: X crashes when
using a new
monitor To: Jon Savage jonathansavage@gmail.com,
Discussions about
development for the Fedora desktop fedora-desktop-list@redhat.com
Jon Savage wrote:
> On Mon, 07 Mar 2005 09:38:11 -0500, Benjamin Jiang > bjiang_ee@yahoo.ca wrote: > >> Hi, all, >> >> I installed a fresh copy of FC3 into my Dad's machine and
everything
>> worked fine. However, when I brought the machine to my Dad's
place and
>> plugged in his monitor (Acer 7154e), X crashes no matter what.
I tried
>> config xorg.conf with the correct HorizSync and VertRefresh,
but it
>> didn't even make any difference. >> > <snip> > Try booting into runlevel 3 and then > login as root and do system-config-display --reconfig. > > Bests > > JS > > Thanks, Jon.
I did that yesterday already and no difference made.
When booting in to run level 3, log in as either a non privaliged user, or as root and running "startx", if X still crashes you should get some output in the terminal.
Also look through the file /var/log/Xorg.0.log, as that will have
some
more information that may help us to help you.
Doug
Doug, I pasted Xorg.0.log at the end of the first email I sent out.
But, here is it again anyway: Xorg.0.log:
My experience is that if X sends the wrong sync to a monitor, all that happens is that the monitor shows a borked picture, or nothing at all exept an error message. X doesn't crash...
My expearience is slightly different.
If X fails to start due to refresh rate issues, then it will fail to start, not "crash" just will stop trying to load.
However this error seems to suggest that it did "crash".
It could be due to a damaged hard disk in transit? Causing a problem with some of the libraries?
Let me try to copy the whole /usr/X11R6 directory from a working FC3 machne then. Is that the only directory? Maybe /usr/lib/X11 as weel?
Ben.
It worked! I coped /usr/X11R6 directory from a working FC3 and it works now. Thanks Douglas!
God, I feel stupid :-o.
Ben.
desktop@lists.fedoraproject.org